manualshive.com logo in svg

WARRIOR 80ENA24, Assembly & Operating Instructions

Share
Download
WARRIOR 80ENA24 Assembly & Operating Instructions Download Page 17

 

15 

SPECIFICATION 

Pull, Speed, Amperes, Volts (First layer): 

Line Pull 

Line Speed ft/min (m/min) 

Current   A 

Ibs (kgs) 

24V DC 

24V DC 

0 

33.8(10.3) 

26 

4409(2000) 

11.5(3.5) 

95 

8818(4000) 

8.5(2.6) 

140 

13228(6000) 

6.6(2.0) 

190 

17637(8000) 

5.9(1.8) 

230 

Line Pull And Rope Capacity In Layer 

Layer 

Rated line pull lbs (kgs) 

Total rope on the drum ft (m) 

1 

17637 (8000) 

18.7(5.7) 

2 

14923(6769) 

42.7(13) 

3 

12932(5866) 

70.2(21.4) 

4 

11408(5175) 

92(28) 

 

 
 

Rated line pull 

8000 kgs (17637 lbs)  

Motor: series wound 

24V:Input: 6.1kW / 8.2hp; Output: 3.1kW / 4.2hp 

Gear reduction ratio 

450:1 

Cable (Dia.

×

 L) 

80ENS24 

80ENA24 

Ø9/16"

×

87 ' (Ø13.8mm

×

26.5m) 

Ø9/16"

×

92 ' (Ø14mm

×

28m) 

Drum size (Dia.

×

 L) 

Ø5.43 "

×

7.7 " (Ø138mm

×

196mm) 

Mounting bolt pattern 

10 "

×

4.5 " (254mm

×

114.3 mm)  

10 "

×

7.5 " (254mm

×

190.5mm) 

Overall dimensions 

(L

×

W

×

H) 

25"

×

13.1"

×

11.6" 

635 mm 

×

333mm 

×

294mm 

Summary of Contents for 80ENA24


















Reviews:

No comments

Brands by name

Popular brands

Load more brands