background image

DAILY

 

 

 

Test brake effectiveness before you drive 
Recharge batteries fully every night  
  

WEEKLY 

 

 

 

Check tire pressure, pressure should be 40-50 psi  
Check and tighten the throttle screw  
Ensure there are no hydraulic leaks  

 

 

MONTHLY

 

 

 

Check battery condition. Clean battery terminals if necessary  
Check all electrical wire connectors to eliminate loose connections  
Tighten all exposed screws and nuts  
Check wheel bearings by spinning tires and check for free rotation.   

  
THROTTLE ADJUSTMENT 

 

 

 

Release the clutch lever, thus the motor can rotate freely.  
Note on the throttle control potentiometer, when the control level is switching, how the mount 
plate retain one end of the spring while the control bracket pulls the other end of the spring in 
the direction of rotation.  As the lever rotates in the opposite direction, the other spring end is 
pulled in the opposite direction.  
With the key in and speed setting at low, rotate the throttle lever until you just hear the brake 
release click and motor starts running.  Notice the angle rotated between the lever and the 
Trolley horn. 

  

 

Rotate the throttle lever in the opposite direction till just brake release clicks, notice the angle 
rotated between the lever and the Trolley horn in this direction. 
 
If the angles are not identical, loose control bracket screws, rotate potentiometer shaft a few 
degrees by using a flat screw driver and then retighten it.  
Repeat until the reverse, neutral and forward are in proper ranges. 
Make sure the throttle control lever is parallel to tiller handle. If the lever is not parallel, full 
range rotation in one direction will not be possible, resulting in loss of speed in that direction.  

 

 

LIMITED WARRANTY 

 

 

 

This warranty is extended only to original consumer purchases of the Trolley either from the 
authorised retailers or representatives.  
  
We warrant the products manufactured by them to be free from defects in materials and 
workmanship for a period of 1 year from the date of purchase for business use.  If, within 
such warrant period, any such products shall be proven to our satisfaction to be defective, 
such product shall be repaired or replaced, at our option.  This warranty does not include any 
shipping charges incurred in replacement part installation or repair of such product.  Our sole 
obligation and your exclusive remedy under this warranty shall be limited to such repair 
and/or replacement. 

Summary of Contents for P2GOARROWMATEHD
















Reviews: