PACK-G/Iss 1/June 18
Drill and countersink 2mm pilot holes through
the top of the shelf at the positions shown
Shelf support panel
Back
bearer
Side
bearer
18mm
18mm
Pre-drilled/
routed holes -
do not cut shelf
from this end
4
Disclaimer:
It is the responsibility of the customer to ascertain that the area for installation is structurally sound and that any drilling necessary will not compromise
electrical wiring, water pipes or gas services. The information provided herein is intended as a guide to good practice. The manufacturer cannot be held responsible or liable
for any damage, wear or malfunction caused to components due to inadequate or improper installation.
3. Fitting the long shelf
Measure the width from the divider panel to the right
hand inside end of the wardrobe and, if necessary, cut
the long shelf down to this size.
IMPORTANT – Cut any excess length from the end of
the shelf that does not have any pre-drilled/routed
holes – see diagram i.
Prior to sliding the shelf into position, we recommend
drilling and countersinking 2mm pilot holes through
the back edge and right end edge of the shelf
(approximately 9mm in from the outside edge) to
enable it to be screwed to the back and side shelf
bearers – see diagram i.
Insert the two remaining minifix housings into the
pre-routed (15mm diameter) holes on the underside of
the long shelf, ensuring that the side with the cross
head is facing outwards. Slide the shelf into position,
ensuring that the two minifix housings locate with the
two minifix bolts protruding from the divider panel and
the two pre-drilled holes in the top of the shelf align
with the corresponding pre-drilled holes in the top
i.
edge of the shelf support panel underneath. Then,
ensuring the shelf is sitting firmly on both back and side
shelf bearers, screw the shelf to the bearers using the
25mm screws provided and use the two M10 direct
drive screws to secure the shelf to the shelf support
panel through the pre-drilled holes. Finally, on the
underside of the shelf, using a crosshead screwdriver,
turn the minifix housings a quarter turn anti-clockwise
to lock the shelf to the bolts on the divider panel.
4. Fitting the hanging rail
To ensure the hanging rail under the shelf is positioned
correctly, use the paper drilling template supplied. See
diagram j to help you position the drilling template
correctly for the right hand end of the hanging rail.
TIP
You may wish to mark the positions for the pilot
holes with a bradawl, remove the template and
then drill the holes; rather than drilling the pilot
holes directly through the paper template.
Once the pilot holes are drilled in the right end shelf
bearer, place the hanging rail bracket in position
(ensuring the U-shaped cup is at the bottom) and using
the 15mm screws provided screw it in place through
the top and bottom holes. Then, locate the pre-drilled
holes in the side of the shelf support panel and fix
another hanging bracket in place there. Measure the
distance between the inside faces of the hanging rail
brackets and cut the hanging rail to length. The
hanging rail can then be placed in position and should
sit securely in the U-shaped cups of the brackets.
230mm
230mm
Drill 2mm diameter
pilot holes
47mm
30mm
10 mm
47mm
30mm
10
mm
HANGING RAIL BRACKETS
DRILLING TEMPLATE
For use with
PACKS
D
,
E
,
F
,
G
and
H
Pla
ce
in
ba
ck
co
rne
r
un
de
r s
he
lf o
n
rig
ht
ha
nd
sid
e
of
wa
rdr
ob
e
Us
e t
he
GR
EY
dr
ill
ho
le
po
sit
ion
s
Plac
e in
bac
k co
rne
r
und
er s
helf
on
left
han
d
sid
e
of w
ard
rob
e
Use
th
e
BLA
CK
drill
ho
le p
osit
ion
s
Shelf
Shelf
Position the drilling template as shown for the
right hand side
hanging rail bracket and use
the
GREY
drill hole positions
Position the drilling template as shown for the
left hand side
hanging rail bracket and use
the
BLACK
drill hole positions
Back
shelf bearer
Right hand
shelf bearer
GREY drill hole
positions
BLACK drill hole
positions
Left hand
shelf bearer
Back
shelf bearer
j. Drilling template position for hanging rail bracket
on right end shelf bearer
Right end shelf bearer
Back shelf bearer
Shelf
