background image

20

D10-991-2400     5/1/04

WANNER ENGINEERING, INC.

1204 Chestnut Avenue, Minneapolis, MN  55403
TEL: (612) 332-5681  FAX: (612) 332-6937
TOLL-FREE FAX [US only]: (800) 332-6812

www.hydra-cell.com
email: [email protected]

©2004 Wanner Engineering, Inc. Printed in USA

Limited Warranty

Wanner Engineering, Inc. extends to the original purchaser
of equipment manufacturerd by it and bearing its name, a
limited one-year warranty from the date of purchase against
defects in material or workmanship, provided that the
equipment is installed and operated in accordance with
the recommendations and instructions of Wanner
Engineering, Inc. Wanner Engineering, Inc. will repair or
replace, at its option, defective parts without charge if such
parts are returned with transportation charges prepaid to
Wanner Engineering, Inc., 1204 Chestnut Avenue,
Minneapolis, Minnesota  55403.

This warranty does not cover:

1. The electric motors (if any), which are covered by the
separate warranties of the manufacturers of these
components.

2. Normal wear and/or damage caused by or related to
abrasion, corrosion, abuse, negligence, accident, faulty
installation or tampering in a manner which impairs normal
operation.

3. Transportation costs.

This limited warranty is exclusive, and is in lieu of any other
warranties (express or implied) including warranty of
merchantability or warranty of fitness for a particular
purpose and of any noncontractual liabilities including
product liabilities based on negligence or strict liability.
Every form of liability for direct, special, incidental or
consequential damages or loss is expressly excluded and
denied.

Summary of Contents for Hydra-Cell G-10





















Reviews: