background image

Click the Load         the 

object which would be 

located in the build area. 

NowClick “3D View” and 

check and adjust the object

to ensure it is placed inside 

the printing area. Press the 

slice button to start 

slicing operation.  

Now open “Slice View” to 

check that the fi rst layer of 

every object is in contact 

with the platform. 

SLICE OBJECT

Go to confi gure slicing profi le Change the 

slice thickness from 0.02 to 0.1; exposure 

time 4000 to 12000(wanhao resin);

Bottom exposure time50000 to 200000

(wanhao resin).  And Click 

“ Apply Changes”  

WANHAO DUPLICATOR 7

GETTING STARTED GUIDE

1

DOWNLOAD AND INSTALL SOFTWARE

Go to www.wanhao3dprinter.com and download “

Creation 

Workshop

” located at “

Download software Duplicator 7

”. The 

latest version is always online.

Extract the fi le and install the software by clicling on CW exe.

2

UNPACK AND CONNECT CABLES

With the printer switched off, connect:

A. Connect the HDMI cable to your

    computer and printer.

B. Connect the USB cable to your 

    computer and Printer. 

C. Set off mode the PC power& mode 

    during Printing process, The sleeping

    mode may effects the printing quality.

D. Connect the power supply to printer.

3

CONFIGURE SCREEN RESOLUTION

Make sure you have the correct resolution on your 

screen as 2560*1440. This may appears sometimes 

as 1440*2560. Note that the right resolution is 

2560*1440.

4

SWITCH ON PRINTER

Turn on the switch behind your computer and 

printer.  Open the software and load the object 

(STL,OBJ or AMF)

CONNECT SOFTWARE AND PRINTER

In Creation Workshop, click on 

“Confi gure”, and then open the 

subfolder “Confi gure Machine”. 

In the confi guration folder 

connect the printer to the 

computer by clicking on the

button“Confi gure”. Select the 

port you have connected the 

USB to and set the speed to 

115200 and data bits to 8. “OK” 

and fi nially press

“ Apply Change”                 To  connect

your computer and the duplicator 7 by clicking the high light 

connecting button       .  After connecting the discounting 

button would be high light             . 

 

 

5

6

TIP:

 If you experience any issue confi guring the screen resolution or usb port.Visit our ivdeo tutorial at WANHAO VIDEO at 

                  www.wanhao3dprinter.com.

PREPARE DUPLICATOR 7 FOR PRINTING

Place vat on top of the LCD screen and tighten vat 

screws to keep it tight on the printer. Make sure that 

don’t tight               the vat too hard that may damage 

the LCD,                 tight enough that the vat shouldn't 

be lift up                  during printing process.

9

Slide the building plate onto the building plate holder.

Make sure the build compound with groove side toward 

the printer.

10

Tighten the Building plate knob and loosen the 

four screws at the sides so the platform can move 

freely up and down.

11

NOTE: 

Ensure that building plate’s screws are completely free when 

lowering the platform to avoide damage the screen.

Now click on the “Control” tab. Press the “Home” 

button to lower the platform towards the screen. 

The platform will move down to be set on the screen 

(level 0 in Z axis.) and stop. 

12

Press the the building platform smoothly with one hand and tighten 4 screws. All 4 screws should be now tighten. Now lift 

the building plate and fi ll the vat with resin. Print don’t consume a lot of resin, a quarter full vat is enough for a medium sized 

print.

13

NOTE

: Don’t push the build platform too hard 

to avoid breaking the LCD screen.Make sure the 

platform touches the screen suffi ciently.

NOTE

:once started, the print can’t be paused and refi lled 

so it's safer to over-fi ll and reuse the resin.

a.

b.

c.

CONFIGURE BUILD SIZE AND SLICE OBJECT

Once connected the printer 

to the computer. Go to 

“ Confi gure Machine” 

Change the build size

exactly to the following 

Pic. By clicking the 

display resolution 2560*1440, 

then click         to add the 

display to software setting. 

Finally click Apply                    to 

admit the change. 

7

8

14

Place the hood back onto the printer. In control

panel press Z home and place the platform on

home position

Z Axi S

Z Axi S

15

Now you are ready to print, Press play after you 

sliced the model. Once the print has finished, The 

CW software shows that “Print 100% complete” and 

will stop.

TIP:

 If you experience any issue confi guring the screen resolution or usb port.Visit our ivdeo tutorial at WANHAO VIDEO at 

                  www.wanhao3dprinter.com.

REV.A

REV.A

Reviews: