MIDI:
Use either the included 3.5mm to MIDI 5-pin DIN adapter to connect a standard MIDI cable, or if connecting
from another pedal that uses 3.5mm TRS audio connectors, use a standard TRS 3.5mm audio cable. To set the MIDI
Channel the device will receive commands on (by default the pedal is in omni channel mode):
1. Power off the device, press and hold the Left Footswitch (Channel 2 switch), and power the device on.
2. After power up, releases the switch. Both LEDs will blink.
3. Send a MIDI CC message CC32 with value set to the desired MIDI channel: val=0 is Channel 1, up to val=15 is
Channel 16, val=16 is omni. The LEDs will blink in success.
NOTE: This CC message may be sent on any channel.
Basic MIDI Commands:
CC Function
CC no.
Value (0-127)
Description
Channel 1 on/off State
0
0=off, 1-127=on
Sets the on/off state of Channel 1 (Ch1)
Channel 2 on/off State
1
0=off, 1-127=on
Sets the on/off state of Channel 2 (Ch2)
Ch1 off, Ch2 off
2
any value
Sets Ch1 off and Ch2 off when this command is received
Ch1 on, Ch2 off
3
any value
Sets Ch1 on and Ch2 off when this command is received
Ch1 off, Ch2 on
4
any value
Sets Ch1 off and Ch2 on when this command is received
Ch1 on, Ch2 on
5
any value
Sets Ch1 on and Ch2 on when this command is received
Power:
This pedal was designed around the usage of a 9-18V DC power source only. To avoid damage to the
pedal, do not exceed 18V DC, do not use center pin positive adapters, and do not use AC power. Use only a 9-18V
DC power source that is intended for guitar pedals. This pedal requires 55mA.
NOTE: We recommend disconnecting the battery if this pedal is used with a power supply. If the power supplied
is insufficient LEDS may flicker when a foot switch is pressed to indicate this.
Volume:
Controls the total output volume of each channel.
Gain:
Turning this control clockwise will increase the amount of gain applied to the signal path of each channel.
Bass / Treble:
Adjust the amount of low-end / high-end frequencies, turning clockwise will increase the levels,
counter clockwise to decrease.
Presence:
Global Presence control to add sparkle and top end to both channels, start off with this turned all the way
counter-clockwise and adjust to suit.
Order:
Change the channel stacking order with this switch if you are using only one input and output cable.
Gain Level (Side switches L and R):
Set the switch at the top for maximum, middle for medium, and bottom
positions for lower gain level settings.
Voicing (Side switches L and R):
Set the switch at the top for Hard clipping (Crunchy), bottom for soft clipping
(Smooth), and in the middle position to blend both clipping styles.
Connections:
This pedal has 2 pairs of input and output jacks: if you are using only one set connect to the jacks
marked with solid triangles; if you are using both sets, the outline triangles indicate the separate output for Channel
1 and input for Channel 2. This allows you to connect both channels independently (e.g to a loop switcher), insert a
pedal between the channels, or run in stereo.
A highly configurable dual overdrive pedal with two
stackable independent MIDI switchable channels:
Channel 1 delivers a classic Blues Breaker tone; Channel 2
is a recreation of the original Pantheon, a similar circuit to
the Blues Breaker but with a modern boutique feel.
@WamplerPedals
@WamplerPedals
/WamplerPedals
YouTube.com/user/WampCat
visit wamplerpedals.com for full manual and product videos
