Waldorf RNL8610E Series Installation And Operation Manual Download Page 15

13 

1.  The grease drawer should be checked and 

emptied frequently to prevent overflow and 

spillage.  Remove the grease drawer while still 

warm so that the grease is in a liquid state.  

Empty any grease from the drawer and wash 

thoroughly in the same manner as any cooking 

utensil. 

2.  Thoroughly clean the splash back, the interior 

and exterior surfaces of the range with hot  

water, a detergent solution and a soft scrubbing 

brush. 

3.  Clean the Control Panel with a damp cloth light-

ly moistened with a solution of mild detergent 

and water.  Dry the control panel thoroughly 

with a dry cloth and polish with a soft dry cloth. 

4.  Brush the griddle surface (optional - if fitted) 

with a soft bristled brush.  Any carbon deposits 

should be removed using the supplied scraper 

tool followed by wiping with a cloth to prevent 

accumulation of food deposits. 

5.  Brush the elements with a soft bristled brush.  

Any carbon deposits should be removed using a 

scraper tool followed by wiping with a cloth 

moistened in a solution of hot water and  

detergent to prevent accumulation of food 

deposits. 

6.  To clean under the elements, carry out the  

following procedure as shown opposite:- 

 

A.  Lift up the element module at the front of 

the cooktop. 

B.  Whilst holding up the front of the element 

module, pull the module as far forward as it 

will come. 

C.  Rotate the element module around the  

element pivot plate on whichever side of the 

cooktop that the pivot plate is located. 

D. Remove the drip tray from beneath the  

element and wash with hot water and a  

detergent solution.  Dry with a soft dry 

cloth. 

Clean beneath the element using a cloth  

moistened in a solution of hot water and  

detergent. 

Refit the drip tray beneath the element  

ensuring that the drip tray is fitted correctly. 

Lower the element module back down to the 

cooktop frame and slide rearwards to fit 

back into position on the cooktop surface. 

 

7.  Dry the range thoroughly with a dry cloth and 

polish with a soft dry cloth. 

Lift up Front of 

Element Module

 

Pull Element 

Module Forwards

 

Rotate Element

 

Support Element and 

Lift Out Drip Tray

 

L/Hand Element  

Pivot Plate

 

R/Hand Element  

Pivot Plate

 

A

 

B

 

C

 

D

 

Summary of Contents for RNL8610E Series


























Reviews: