BRACKET A (LONG)
SIDE STEP
2018/01
RUBBER MOLDING
ADHESIVE SURFACE
■HOW TO FIX THE ATTACHED RUBBER MOLDINGS (STEP 6)
Priming the surface,
then fix the attached
rubber moldings.
ATTACHED
DOUBLE-SIDED TAPE
ATTACHED DOUBLE-SIDED TAPE
OEM TAPPING SCREW
OEM TAPPING SCREW
FRONT
■ HOW TO FIX THE ATTACHED
DOOR PANEL AERO COVERS
(STEP 7)
BRACKET A (LONG)
BRACKET B (SHORT)
GROMMET
OEM TAPPING SCREW
OEM TAPPING SCREW
OEM TAPPING SCREW
【BEFORE PAINTING】
１） Temporarily install WALD Side Steps to the body with the attached brackets.
※ Adjust the details of WALD Sides Steps to fit the body by rasps or sandpapers.
２） Mark the location of Door Panel Aero Covers to the body
with the masking tape after checking the balance.
３） Paint WALD Side Steps and Door Panel Aero Covers.
【AFTER PAINTING】
４） Completely degrease the installation position.
５） Fix the attached brackets on WALD Side Steps.
６） Fix the attached rubber moldings on WALD Side Steps.
７） Use caulking glue and the attached double-sided tape to install WALD Side Steps
and Door Panel Aero Covers to the body.
※ Fold the both ends of release paper to adjust the location.
８） Use OEM tapping screws and the attached bolts to fix WALD Side Steps tightly.
９） Leave them till completely fixed.
ATTACHED BOLT
(M5 x 15)
ATTACHED BOLT
(M5 x 15)
ATTACHED BOLT
(M5 x 15)
Keep the enough clearance to
Open/Close the doors
Fix along with the fender line
C-HR
PARTS
QUANTITIES
SIDE STEP
1 SET
1 SET
1 SET
4
2
3 SETS
6
SIDE STEPS
RUBBER MOLDING
DOOR PANEL AERO COVERS
BRACKET A (LONG)
BRACKET B (SHORT)
BOLTS (M5 X 15)
GROMMET
(2017y )
ZYX10
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD SIDE STEPS FOR TOYOTA ZYX10 C-HR.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ATTENTION
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
