background image

Warning

1.3 Safety Precautions

The owner shall pay attention to the followings when placing, checking 

and repairing machine to insure player’s security and avoid damage:

Make sure to plug the game into 110V or 220V main outlet to avoid fire 

and electric shock.

please check  the voltage is 110V or 220V before the machine connectes

 to the power supply,or it may cause a fire or electric shock.

Do not unplug or plug the plug instantly.

Don’t touch the power plug with a wet hand to avoid electric shock.

Don’t expose the power cord/grounding line on the passageway. 

Failure to do this will damage the power cord, causing electric shock 

or short circuit.
Don’t lay anything near the power cord to avoid fire.

Do not pull the power cord when unplugging, please hold the plug to

avoid power cord damage, causing fire or electric shock.

Only use fuse and spare parts specified by our company

Connect the connector firmly and tighten the screws.

It is forbidden to push or pull the game-machine in order to prevent the 

accidental danger.
Do not dismount, replace or convert the product without our permission

in order to avoid damage and human injury due to improper operation.
Check and maintain the machine regularly.
Keep “Warning stickers” clean and legible. Replace it immediately 

when the words are not legible or the dirt can’t be removed.
Please contact our service center when performing any work that is 

not described in this manual, and follow the instruction provided.

Make sure to turn off the power when performing maintenance and 

service to avoid electric shock or short circuit.

In case of power cord damage, please contact the local distributor for

replacement

Summary of Contents for PUSHING POINTS


























































































































Reviews: