52
Parameterizing
WAGO-SPEEDWAY 767
767-4801/000-800 8DO 24V DC 0.5A IF (8xM8)
Manual
Version 1.1.0
Pos: 30.9 /Serie 767 (WAGO-SPEED WAY)/Par ametrieren/I/O-M odule/Parametri erung 767- 4801, - 02, -05, -06, 58xx, 7401 Globale Diagnosen @ 7\mod_1265877071562_21.docx @ 50302 @ @ 1
Table 25: Information about existing module diagnostics
Global Diagnostics
Diagnostics
Description
Low voltage of U
LS
Disabling the outputs.
If there is an undervoltage of U
A
and/or U
LS
, the
module outputs are disabled. Machine components can
be placed in a dangerous condition, as well as
personnel and machine put in danger.
If an undervoltage of the logic and sensor supply U
LS
of < 18 V occurs
on the module, the outputs are disabled and a corresponding diagnostic
is transmitted to the fieldbus coupler. The F-LED of the module
illuminates.
Low voltage of U
LS
Disabling the outputs.
If there is an undervoltage of U
A
and/or U
LS
, the
module outputs are disabled. Machine components can
be placed in a dangerous condition, as well as
personnel and machine put in danger.
If an undervoltage of the actuator supply U
A
of < 18 V occurs on the
module, the outputs are disabled and a corresponding diagnostic
transmitted to the fieldbus coupler. The module F-LED illuminates.
Pos: 30.10 /Serie 767 ( WAGO-SPEED WAY)/Parametrier en/I/O-Module/Parametrier ung Kanaldi agnosen Kurzschl uss/Überlast Aktor @ 8\mod_1278414485725_21.docx @ 59134 @ @ 1
Table 26: Information about an existing channel diagnostic
Channel Diagnostics
Diagnostics
Description
Actuator short
circuit/overload
The module has identified a short circuit or overload on the
corresponding channel (1 … 8) (only enabled when the actuator output
is switched on).
Pos: 30.11 /Serie 767 ( WAGO-SPEED WAY)/Parametrier en/I/O-Module/Parametrier ung Kanaldi agnosen U nterbr echung 48xx @ 8\mod_1278481912988_21.docx @ 59214 @ @ 1
Actuator open load
The module has identified a disruption on the corresponding channel
(1 … 8) only enabled when the actuator output is switched off).
Pos: 30.12 /Serie 767 ( WAGO-SPEED WAY)/Parametrier en/I/O-Module/Parametrier ung Kanaldi agnosen Ü bertemper atur 48xx @ 10\mod_1306933498784_21.docx @ 73520 @ @ 1
Overtemperature
The module has identified overheating on the corresponding channel
(1 … 8) (only enabled when the actuator output is switched on).
Pos: 30.13 /Serie 767 ( WAGO-SPEED WAY)/Wichtige Erläuter ung en/Sicherheitshinweise/Hinweis/Hi nweis: U nterbrechung S-BU S 48er @ 8\mod_1278393489593_21.docx @ 59044 @ @ 1
Interruption of the S-BUS
If there is an interruption of the S-BUS, the module is automatically put in STOP
mode. The module outputs are disabled.
Pos: 30.14 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
