WAGO 765-4203/0100-0000 Product Manual Download Page 106

Page: 106 / 122

765-4203/0100-0000

Diagnostics

106

Product manual | Version: 1.0.0
4PORT IOL-A FLD EC DC 24V 2.0A

Parame-
ters

Datatype Description

Parame-
ter 3
Flags

UINT16

Describes the type of parameter 3

Bits 12–15 = 0

Bits 0–11 = data type index of the data type of parameter 3

0x0005: UINT8

The corresponding text parameters and formatting are de-
scribed in document ETG.2000.

Parame-
ter 3

UINT8

Event Qualifier

Table 81: Event Qualifier

Bit

Name

Description

Bits 6–7

Mode

0: reserved

1: single event

2: event disappears

3: event appears

Bits 4–5

Type

0: reserved

1: notification

2: warning

3: error

Bit 3

Source

0: device (remote)

1: master/port

Bits 0–2

Instance

0: unknown

1–3: reserved

4: application

5–7: reserved

11.2.1.9 Emergency Error Codes

The following emergency error codes are defined in the EtherCAT specification:

Table 82: Emergency Error Codes

Emergency Error Code (hex)

Description

00xx

Error Reset or No Error

10xx

Generic Error

20xx

Current

21xx

Current, device input side

22xx

Current inside the device

23xx

Current, device output side

30xx

Voltage

31xx

Mains Voltage

32xx

Voltage inside the device

33xx

Output Voltage

40xx

Temperature

41xx

Ambient Temperature

42xx

Device Temperature

50xx

Device Hardware

60xx

Device Software

61xx

Internal Software

Summary of Contents for 765-4203/0100-0000



























































































































Search results

Summary of Contents for 765-4203/0100-0000

Reviews:

Related manuals for 765-4203/0100-0000

Brands by name

Popular brands

WAGO 765-4203/0100-0000, Product Manual

Search results

Summary of Contents for 765-4203/0100-0000

Reviews:

Related manuals for 765-4203/0100-0000

Brands by name

Popular brands