background image

WAGO-TO-PASS® 761 

Important Notes 

13 

761-112 Telecontrol Module Compact, Web 

 

 

Manual 

 

Version 2.0.0  

 

 

 

 

Please note the following information about FCC Part 15! 
 
FCC Part 15.19

  

This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following conditions: 
1. this device may not cause harmful interference, and 
2. this device must accept any interference received, including interference that 
may cause undesired operation.  
 

FCC Part 15.21

  

Modifications not expressly approved by this company could void the user's 
authority to operate the equipment..  
 

Installation by qualified electrician only

 

The 

TO-PASS

®

 telecontrol module must be operated with Antenna 758-0963.  

The antenna gain main not exceed 3 dBi.  
Only qualified staff can install and maintain the 

TO-PASS

®

 remote module and its 

antenna. The transmitted must be off when working on or nearer to the antenna 
than specified below.  
 

HF-Exposition

  

The external antenna operated with the 

TO-PASS

®

 remote module must be at least 

20 cm away from people. The antenna may not be positioned, so that it works in 
conjunction with any other antenna or transmitter. 

 

 

 

 

 

Hot surface! 

The surface of the housing can become hot during operation. If the device was 
operated at high ambient temperatures, allow it to cool off before touching it. 

 

 

 

 

 

Do not reverse the polarity of connection lines! 

Avoid reverse polarity of data and power supply lines, as this may damage the 
devices involved. 

 

 

 

 

 

Replace defective or damaged devices! 

Replace defective or damaged device/module (e.g., in the event of deformed 
contacts), since the long-term functionality of device/module involved can no 
longer be ensured. 

 

 

Summary of Contents for 761-112













































































































Reviews: