background image

26 

Process Image 

WAGO-I/O-SYSTEM 750 

 

 

753-466 2 AI 4-20 mA S.E. 

 

Manual 

 

Version 1.5.0  

Pos: 59 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Prozessabbild - Ü berschrift 1 @ 4\mod_1240983067828_21.docx @ 31942 @ 1 @ 1 

 

Process Image 

Pos:  60.1 /Serie 750 (WAGO-I/O-SYST EM)/Prozessabbild Kl emmenbus/Anal ogei ngangsklemmen/Pr ozessabbild 750- 0466/-0454 Einl eitung - ohne Vari anten @ 30\mod_1500546933024_21.docx @ 455703 @  @ 1 

 

The 753-466 I/O module provide 1 status byte (8 bits) and 1 data word (16 bits). 

Pos:  60.2 /Serie 750 (WAGO-I/O-SYST EM)/Prozessabbild Kl emmenbus/Anal ogei ngangsklemmen/Pr ozessabbild 750- 0466/-0454 Einl eitung @ 16\mod_1373284271909_21.docx @ 125695 @  @ 1 

 

Whether the status byte is read out via the fieldbus depends on how diagnostic 

information is transmitted by the respective fieldbus or fieldbus 

couplers/controllers used. In any case, the status byte can be read out using the 

WAGO-I/O-CHECK commissioning tool via the service port of the fieldbus 

coupler/controller. 

The digitalized measured value is transmitted to the process image of the fieldbus 

coupler/controller in a data word (16 bits) as an input byte 0 (low) and input byte 

1 (high). This value is mapped with a resolution of 12 bits on bit B3 ... B14. Status 

information, which can be evaluated for fault detection, is contained in the three 

least significant bits (B0 ... B2). 

If the measurement is above the measuring range, bit B0 is set = 1, and if the 

measurement is below the measuring range or if a wire breaks, bits B0 and B1 are 

set = 1. 

Pos:  60.3 /Serie 750 (WAGO-I/O-SYST EM)/Prozessabbild Kl emmenbus/Hinweis: Prozessabbil dmapping abhängig von FBK/PFC, mit Status-/C ontroll byte @ 4\mod_1242621308640_21.docx @ 33290 @  @ 1 

 

 

 

 

Mapping of process data in the process image of fieldbus systems 

The representation of the I/O modules’ process data in the process image depends 

on the fieldbus coupler/controller used. Please take this information as well as the 

particular design of the respective control/status bytes from the section “Fieldbus 

Specific Design of the Process Data” included in the description concerning the 

process image of the fieldbus coupler/controller used. 

 

Pos: 60.4 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810  @   @  1 

 

 

 

Summary of Contents for 753-466





















































Reviews: