WAGO 750-641 Manual Download Page 19

Page: 19 / 36

750-641 [DALI/DSI Master Module]

•

Process Data

WAGO-I/O-SYSTEM 750
I/O Modules

2.1.1.6.2.4 DALI Addressing Sheme

Every DALI device (electronic ballast) is able to react to a short address, 16
group addresses and broadcast. Each type of addresses is coded in an address
byte.

Address type

Address byte

Short or group address

YAAA AAAS

64 Short addresses

0AAA AAAS

16 Group addresses

100A AAAS

Collective address

111 111S

Y: Address type:

Y=‘0‘ Short address,

Y=‘1‘ Group address or collective address

A: Significant address bit
S:

Selection bit:

S=‘0‘, Direct lamp power value is following

S=‘1‘, Command is following in the next byte

2.1.1.6.2.5 Command Sets acc. to DIN IEC 60929 (dated: Draft July 2001)

DALI Commands (Request)

Output Data

No.

Command

Code

DALI

Address

Function

0000 0000

YAAA AAA1

0000 0000 Off

0000 0001

YAAA AAA1

0000 0000 Up

0000 0010

YAAA AAA1

0000 0000 Down

0000 0011

YAAA AAA1

0000 0000 Step up

0000 0100

YAAA AAA1

0000 0000 Step down

0000 0101

YAAA AAA1

0000 0000 Recall Max – Level

0000 0110

YAAA AAA1

0000 0000 Recall Min – Level

0000 0111

YAAA AAA1

0000 0000 Step down and off

0000 1000

YAAA AAA1

0000 0000 On and step up

9-15

0000 1XXX

YAAA AAA1

0000 0000 Reserved

16-31 0001 XXXX

YAAA AAA1

0000 0000 Go to scene 1 - 16

32 *) 0010 0000

YAAA AAA1

0000 0000 Reset

33 *) 0010 0001

YAAA AAA1

0000 0000 Store actual Level in the DTR **)

34–41
*)

0010 XXXX

YAAA AAA1

0000 0000 Reserved

42 *) 0010 1010

YAAA AAA1

0000 0000 Store the DTR **)

as Max – Level

43 *) 0010 1011

YAAA AAA1

0000 0000 Store the DTR **)

as Min – Level

44 *) 0010 1100

YAAA AAA1

0000 0000 Store the DTR **)

as System Failure – Level

45 *) 0010 1101

YAAA AAA1

0000 0000 Store the DTR **)

as Power On Level

46 *) 0010 1110

YAAA AAA1

0000 0000 Store the DTR **)

as Fade Time

47 *) 0010 1111

YAAA AAA1

0000 0000 Store the DTR **)

as Fade Rate

48–63
*)

0011 XXXX

YAAA AAA1

0000 0000 Reserved

64-79
*)

0100 XXXX

YAAA AAA1

0000 0000 Store the DTR **)

as Scene1 -16

80-95
*)

0101 XXXX

YAAA AAA1

0000 0000 Remove from Scene 1 - 16

96-
111 *)

0110 XXXX

YAAA AAA1

0000 0000 Add to Group 1 - 16

112 *) 0111 XXXX

YAAA AAA1

0000 0000 Remove from Group 1 -16

128 *) 1000 0000

YAAA AAA1

0000 0000 Store the DTR **)

as Short Address

129–
143

1000 XXXX

YAAA AAA1

0000 0000 Reserved

144

1001 0000

YAAA AAA1

0000 0000 Query Status

145

1001 0001

YAAA AAA1

0000 0000 Query Ballast

146

1001 0010

YAAA AAA1

0000 0000 Query Lamp Failure

147

1001 0011

YAAA AAA1

0000 0000 Query Lamp Power On

148

1001 0100

YAAA AAA1

0000 0000 Query Limit Error

Summary of Contents for 750-641





































Search results

Summary of Contents for 750-641

Reviews:

Related manuals for 750-641

Brands by name

Popular brands

WAGO 750-641, Manual

Search results

Summary of Contents for 750-641

Reviews:

Related manuals for 750-641

Brands by name

Popular brands