WAGO 750-494 Series Manual Download Page 99

Page: 99 / 134

WAGO-I/O-SYSTEM 750

Diagnostics

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 101 /Alle Serien (Allgemei ne M odul e)/Ü berschriften/Ebene 1/Di agnose - Überschrift 1 @ 4\mod_1240831069471_21.docx @ 31372 @ 1 @ 1

Diagnostics

Pos: 102 /Serie 750 (WAGO-I/O-SYST EM)/Diagnose/Busklemmen/Diagnose 750- 0494, - 0495 @ 13\mod_1348662372924_21.docx @ 103550 @ @ 1

LED A indicates the operating status, LEDs B … H indicate possible errors.

The meaning of these indications is as follows:

Table 22: Diagnostics

LED

State

Message

Off

No operational readiness or

the internal data bus communication is interrupted.

Note: If the watchdog was disabled, the LED is

always green. See section “Commissioning” >

“Configuration with WAGO-I/O-

CHECK

”.

Green

Operational readiness and correct internal data bus

communication

Off

No error

Red

General error message for L1:

Under-/overvoltage or overcurrent

Off

No error

Red

General error message: Clipping of a current

measuring path IL1, IL2 or IL3

Off

No error

Red

High measuring error, caused by undershooting the

min. voltage at L1, L2 or L3

Off

No error

Red

General error message for L2:

Under-/overvoltage or overcurrent

Off

No error

Red

General error message for L3:

Under-/overvoltage or overcurrent

Off

No error

Red

General error message: Clipping of a voltage

measuring path L1, L2 or L3

Off

No error

Yellow Error of the phase sequence L1-L2-L3

Pos: 103 /Dokumentati on allgemei n/Gli ederungsel emente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands