background image

EN

G

LIS

H

EN

G

LIS

H

10

iOnBoost

 V8 by Wagan Tech

®

8. When the clamps are properly connected to the battery, the green light on the cable unit

safety block will illuminate (a three-second delay is normal). When the light illuminates steady

green, it is safe to proceed in these instructions. If the light fails to illuminate steady green or if

any red lights illuminate, consult the troubleshooting section of this manual.

9. Place unit on a secure surface away from moving parts.
10. Start vehicle engine. Stop if the vehicle does not start after 3 to 4 seconds of engine cranking.

Wait 3 to 4 minutes, then try again. If engine does not start after second attempt, discontinue

cranking and consult a professional.

11. The internal safety timer will automatically disconnect the circuit after 30 seconds to prevent

the vehicle battery from reverse charging the unit. If your vehicle still has not started,

disconnect the cables and try the procedure again.

12. When finished, disconnect the clamps in reverse sequence of connecting procedure—

first disconnect negative (black), then positive (red) clamps. Do not let the clamps touch

each other.

13. Disconnect the jumper cable assembly from the unit.
14. When convenient, using either AC or DC charging adapter, completely charge the

iOnBoost battery.

15. Store the unit and charge adapters in a cool, dry environment, away from flammable

materials. Remember to fully charge the unit every three months.

TROUBLESHOOTING

Jumpstart Warning Lights

The iOnBoost is ready to jumpstart when the cables are connected and a steady green light 

illuminates on the cable safety block. The following chart displays the combinations of warning 

lights that occur when the iOnBoost fails to display the ready light:

Warning lights

Type of warning

Solution

Flashing red 

and green 

lights

No vehicle battery 

detected

Cables are not properly connected. Check cable 

connection. Check terminals for corrosion.
Check battery status indicator light on iOnBoost, 

recharge iOnBoost if needed.

Solid red light 

with beeping 

sound

30-second timer

has expired or iOnBoost

charge is too low for

charging.

Disconnect iOnBoost and follow connection procedure 

again. Charge iOnBoost, if necessary.

Solid red light 

with rapid 

beeping sound

Short-circuit or 

reverse polarity

Disconnect immediately and follow connection 

procedure again.

No lights

Overload or overheat Allow unit to cool for 10 minutes. Plug into AC charger 

to reset iOnBoost.

Summary of Contents for 7502












Reviews: