background image

WAFER GSM-RELAY REMOTE CONTROL UNIT 

http://www.waferstar.com 

#REPLY SMS reply enable or disable for relay output control command

 

This command is used to save the cost for SMS reply when no need the SMS reply back 

#PWD123456#REPLY=ON or #PWD123456#REPLY=OFF

 

When REPLY=OFF,then any relay output control text command would no confirmed SMS reply 
from controller,including the OUT, RLY and the Customized Text Command 
 

#WHL White List

This is the command that you will use most. it is used to add or remove numbers that are enabled 
to control the relay sets into the White List. You can add up to 200 numbers in the list. Every 
position must be indicated in the command and we advise you to keep a list written somewhere to 
know which numbers are in and in which position. 

• To add a number with SMS, the syntax of the command is the following: 

#PWD123456#WHL01=61143815 

Acknowledge 

would be : 

WHL01 SET TO 61143815 OK

 

Where 01 is the position in the list and 61143815 is the number enabled. 
Please note that it is possible to program up to a maximum of 18 digits for a number. If it has 
more digits you should use the rightmost ones. For example, if your number is 33446665555 you 
should program 3446665555. If your number appears as +85261143815 you should not program 
the country code (+852). If your number has only 17 digits or less, it is not a problem. The 
important thing is that you don't exceed 18 digits. 

• To add a new number,you also can use the fast teaching button

   

(only from WHL01 to WHL10) 
Press the button KEY1 for around 2 to 3 second and then the LED D1 would be lighting,and then 
you can use the phone to call the device number and then device would reject the calling and the 
LED D1 would flash one or two times,then the number would be saved. If you need to continue to 
program,then just use another phone to call the device. If you don’t need to program more ,then 
just press the KEY1 button again to QUIT the teaching process,then the LED D1 would be OFF. 
Then you can use the numbers just programmed into the device to control the device. 

(Fast Button program only support the program from WHL01 to WHL10,if it is full,then after 
you press the teach button,the LED would flash sometimes,and Quit the process automatically) 

 
• To check which is the number in a place of the list: 

#PWD123456#WHL01? 

Acknowledge 

: WHL01 IS 61143815 OK 

• To erase a number: 

#PWD123456#WHL01=0000000 

(or you can write over it another number you wish to add) 
Acknowledge : 

WHL01 SET TO 00000000 

List All numbers in the List 

#PWD123456#WHL=ALL?  

(

PC)

 

Acknowledge 

:  

WHL01 IS XXX 

WHL03 IS XXX 

WHL08 IS XXX 

Summary of Contents for GSM-RELAY













Reviews: