Waekon PWM Power Pro 78065 User Manual Download Page 12

Warranty

Subject to the conditions that follow and are noted below, this product is warranted to be free from 

defects in material and workmanship, under proper use and in accordance with the manufacturer’s written 

recommendation and specifications, for a period designated below on all products:

This product carries a one year limited warranty.

The manufacturer’s obligation under this warranty is limited to unaltered products returned to the 

manufacturer by the initial end user of the new products. Therefore, this warranty does not cover any 

products resold by the end user to third parties, nor any reconditioned products sold as such, by the 

manufacturer. The sole remedy for any such defect shall be the repair, or replacement, of the product at 

the sole discretion of the manufacturer. This warranty does not cover expendable parts, such as batteries, 

nor does it cover shipping or handling. In addition, manufacturer is not liable for any loss or damage to 

product during shipping.
In the event it is determined that the product has been tampered with, or altered in any way, this warranty 

is void and all claims against the product will not be honored. All warranty claims must be submitted as 

outlined by the manufacturer and shall be processed in accordance with the manufacturer’s established 

warranty claim procedures. These procedures include provisions that proof of purchase must be established 

(by either warranty card from the seller or by point of purchase receipt) and that the manufacturer will 

make every attempt to return ship the product within one business day from receipt of the returned 

product, freight prepaid.
In addition, all maintenance procedures, as outlined by the product manuals, should be followed for the 

warranty to be kept in force. Should the product not be used in accordance with procedures as specified, 

or if the product otherwise fails outside of the warranty, the manufacturer reserves the right to make such 

judgment and the party returning the product will be notified that written notification will be necessary 

to repair the product at a cost which the manufacturer deems as reasonable. The product will then be 

shipped back to the customer, COD; or as the manufacturer deems appropriate.
This is the only authorized manufacturer’s warranty and is in lieu of all other expressed, or implied, 

warranties or representations, including but not limited to any implied warranties of merchantability or 

fitness or any other obligations on the part of the manufacturer. In no event will the manufacturer be 

liable for business interruptions, loss of profit, personal injury, costs of delays, or any special, indirect, 

incidental or consequential damages, costs or losses.

Summary of Contents for PWM Power Pro 78065













Reviews: