background image

GV 7000A / 7003A

Safety Information

wc_si000108gb.fm

5

2.1

Operating Safety

BACKFEED FROM THE GENERATOR INTO THE PUBLIC POWER
DISTRIBUTION SYSTEM CAN CAUSE SERIOUS INJURY OR
DEATH TO UTILITY WORKERS!

Improper connection of generator to a building's electrical system can
allow electrical current from the generator to backfeed into utility lines.
This may result in electrocution of utility workers, fire, or explosion.
Connections to a building's electrical system must be made by a
qualified electrician and comply with all applicable laws and electrical
codes.

If connected to a building's electrical system the generator must meet
the power, voltage, and frequency requirements of the equipment in
the building. Differences in power, voltage, and frequency
requirements may exist and improper connection may lead to
equipment damage, fire, and personal injury or death. 

Familiarity and proper training are required for the safe operation of
equipment. Equipment operated improperly or by untrained personnel
can be dangerous. Read the operating instructions contained in both
this manual and the engine manual and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the equipment before
being allowed to operate the machine.

2.1.1

NEVER operate the generator when open containers of fuel, paint, or
other flammable liquids are near.

2.1.2

NEVER operate the generator, or tools attached to the generator, with
wet hands.

2.1.3

NEVER use worn electrical cords. Severe electrical shock and
equipment damage may result.

2.1.4

NEVER run the electrical cords under the generator, or over vibrating
or hot parts.

2.1.5

NEVER enclose or cover the generator when it is in use or when it is
hot.

2.1.6

NEVER overload the generator. The total amperage of the tools and
equipment attached to the generator must not exceed the load rating
of the generator. 

2.1.7

NEVER operate the machine in snow, rain, or standing water.

2.1.8

NEVER allow untrained personnel to operate or service the generator.
The generator set should be set up by a trained electrician.

2.1.9

ALWAYS store the equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the reach of
children.

DANGER

WARNING

Summary of Contents for GV 7000A









































Reviews: