manualshive.com logo in svg

Wacker Neuson ET12 02, Operator'S Manual

Share
Download
Wacker Neuson ET12 02 Operator'S Manual Download Page 179

BA ET18, 20, 24 en*  1.5 * et18_20_24w700.fm 

7-1

Maintenance

7

7

 Maintenance

7.1

Information on maintenance

Responsibilities and prerequisites

The working order and the service life of machines are heavily dependent 
on maintenance.
Daily and weekly servicing and maintenance must be performed by 
specifically trained personnel.
Have the maintenance, delivery inspection and the entries in the service 
booklet performed by a Wacker Neuson service center, otherwise 
warranty claims will not be acknowledged.
It is therefore in the interest of the machine owner to perform the 
mandatory maintenance.
This is necessary to ensure optimal functioning. Immediately repair or 
replace parts that are already damaged or not working properly before 
they are due for replacement.
Repair or replacement of safety-relevant parts may be performed only by 
a Wacker Neuson service center.
Repair or replacement of safety-relevant parts may be performed only by 
a Wacker Neuson service center.
The manufacturer shall not be liable for damage to the machine or injury 
caused by failure to observe the specific information and descriptions

Important safety instructions on maintenance

• Follow all safety instructions given in this Operator’s Manual.
• Follow the instructions given in chapter 

Safety,

 

safety instructions 

on maintenance

 and 

qualification of the operating and mainte-

nance personnel

 in this Operator’s Manual.

• Follow the maintenance and safety instructions given in the Operator’s 

Manuals of the attachments.

• In order to avoid injury hazard, do not perform work on a hot and 

running engine.

• Wear protective gloves and clothing.
• Observe the danger indications and safety instructions during mainte-

nance.

• Use a suitable container to collect fluids and lubricants as they flow out 

and dispose of them in an environmentally friendly manner.

• Attach a warning label to the control elements (for example, 

“Machine 

being serviced, do not start”

).

• Stop the machine (see Preparing lubrication).

Maintenance

Summary of Contents for ET12 02































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands