Wacker Neuson BTS 930-8340 Repair Manual Download Page 17 | Manualshive

Page: 17 / 44

background image

BTS Repair

Ignition System

wc_tx000299gb.fm

15

4.5

Removing/mounting the flywheel

See Graphic: wc_gr001395

Removing

4.5.1

Block the piston using the piston stop wedge.

4.5.2

Unscrew bolt (2) and remove washer (3).

4.5.3

Remove flywheel with pulling device 0037576 (a).

CAUTION: To avoid damage to the crankshaft, always use the
protective cap included with the pulling device.

Mounting

4.5.1

Before mounting the flywheel, the cone seat and the crankshaft (4)
must be cleaned.

4.5.2

The flywheel is tightened with a torque of 23 ft.lbs. (30 Nm).

wc_gr001395

2

3

a

4

«
...
15
16
17
18
19
...
»

Summary of Contents for BTS 930-8340













































Reviews:

No comments

Related manuals for BTS 930-8340

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 10

Brand: Aastra Pages: 2

Brand: Aastra Pages: 49

Brand: Aastra Pages: 2

Brand: Aastra Pages: 4

Brand: Uniden Pages: 6

Brand: Panasonic Pages: 23

Brand: Powerplus Pages: 14

Brand: Gartenteile Pages: 144

Brand: Femi Pages: 140

Brand: Powermatic Pages: 48

Brand: Gigaset Pages: 15

SYSTEM 20V TJPS70AL

Brand: Tryton Pages: 56

Brand: Ryobi Pages: 14

Brand: Uniden Pages: 64

Brand: Grizzly Pages: 92

Brand: Chicago Electric Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands