Wacker Neuson 0610049 Operator'S Manual Download Page 41 | Manualshive

Page: 41 / 54

background image

Maintenance

T01007GB.fm

39

7.6

Hydraulic control

7.6.1

Check oil level

1. Move centre pole into vertical position.

2. Open filler bore (1).

3. Oil level must coincide with marking (a), top up with hydraulic fluid if

necessary (see Technical Data).

4. Close filler bore..

7.6.2

Venting hydraulic control

1. Remove apron (4) by undoing the screws (3).

2. Move centre pole into vertical position, move shift lever (2) right into

the reverse position, open filler bore.

3. Loosen connecting screw (5).

4. Slowly push the shift lever into forward motion direction until

hydraulic oil emerges bubblefree at the connection screw.

5. Tighten connecting screw, mount apron.

6. If necessary, top up with, seal filler bore.

«
...
39
40
41
42
43
...
»

Summary of Contents for 0610049























































Reviews:

No comments

Related manuals for 0610049

Brand: Oemtools Pages: 8

Brand: C&H Technologies Pages: 24

Brand: Universal Tool Pages: 2

Brand: Valcom Pages: 3

Brand: Xantrex Pages: 90

MICRO-Router MOF

Brand: Proxxon Pages: 16

Brand: Prym Pages: 2

Brand: Parkside Pages: 65

Brand: ERBA Pages: 75

Brand: Gage Bilt Pages: 24

Brand: stellar labs Pages: 22

Brand: Baileigh Pages: 24

Brand: GYS Pages: 48

Brand: Ferm Pages: 120

Brand: Yost Vises Pages: 6

Brand: Grizzly Pages: 2

GLASSMAN EJ Series

Brand: XP Pages: 59

Brand: Mountz Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands