background image

4211-7, S.7 

Operation  &  Maintenance  Instruction

 

Page 1 of 10 

September,  2017 

 

 

 
 

 

VX™ VENT VALVE PORTION, PART NO. 699505

 

 

 
 
 

 
 
 

 

SEPTEMBER, 2017 

Supersedes  issue  dated  December, 2003 

 

 

 

 

NOTE:  The  following  description  and 
operation is based on this device and its 
components being new or this device and 
its  components  having  been  repaired, 
tested,  installed  and  maintained  in 
accordance with instructions issued by 
this  and  any  other  applicable  Wabtec 
Corporation publications.

 

 

 

  WARNING:

   At  the  time  any  part  is 

replaced in this device, the operation of the 
complete  device  must  pass  a  series  of 
tests  prescribed  in  the  latest  issue  of  the 
applicable Wabtec Test Specification. At the 
time  this  device  is  applied  to  the  brake 
equipment  arrangement,  a  stationary 
vehicle test must be made to insure that this 
device functions properly in the total brake 
equipment  arrangement.  (Consult  your 
local 

Wabtec 

Corporation 

Representative  for  identity  of  the  test 
specification,  with  latest  revision  date,  that 
covers this device.) 

 

IMPORTANT:

  Only  Wabtec  Corporation 

supplied parts are to be used in the repair 
of this device in order to obtain satisfactory 
operation.  Commercially  available  non- 
O.E.M. parts are unacceptable. 

 

NOTE:

  The  part  numbers  and  their 

associated descriptions are the property of 
Wabtec  Corporation  and  may  not  be 
replicated  in  any  manner  or  form  without 
the prior sole written consent of an Officer of 
Wabtec Corporation

.

 

 

 

™ Trademark of Wabtec Corporation 

© 2017 Wabtec Corporation. All rights reserved 

Summary of Contents for VX











Reviews: