Wabtec Ricon TITANIUM S Series Service Manual Download Page 17 | Manualshive

Page: 17 / 76

Wabtec Ricon TITANIUM S Series Service Manual Download Page 17

2 - 4

INSTALLATION

JUNE 2021

32DSKF02.D

TITANIUM S-SERIES AND K-SERIES

PUBLIC USE SERVICE MANUAL

RSM0004600

FIGURE 2-10: BUS BASEPLATE HOLES

CAUTION

Before drilling holes, verify that underlying wires and tubing will not be damaged.

c.

Fasten

Lift:

1) Insert ten 4" x 3/8" carriage bolts through baseplate and vehicle floor.
2) Refer

to

Figure 2-9

. Install five clamping bars on bolts underneath vehicle floor (across baseplate), i.e.,

from 1 to 6, 2 to 7, etc, and secure lift to vehicle floor with 3/8" washers, lock washers and hex-nuts.

3) Use care when tightening carriage screws to prevent baseplate warpage. If baseplate assembly warps,

vertical arms will not be parallel. Make corrections by shimming at appropriate locations. To help pre-
vent warping, tighten the eight carriage bolts to 28 ft. lbs. in the following sequence:

3, 8, 2, 4, 7, 9, 1, 5, 6, 10

NOTE:

Vertical arms must be parallel for proper operation. Adjust bolts as required. Best results are obtained
when lift is mounted on plywood. Shims, although best avoided, may be used if required.

«
...
15
16
17
18
19
...
»

Summary of Contents for Ricon TITANIUM S Series













































































Reviews:

No comments