79
7.
Safety devices and recommendations
In order to make working with our drilling and milling machines safe, we have equipped them with
the following safety devices and are thus in accordance with the relevant European safety
regulations.
1.
Protective cover
(Protective partition) attached to the machine housing, prevents reaching in and coming into
contact with the work spindle. This safety device is constructed in such a way that it can be
adjusted to the necessary working height (depending on the dimensions of the workpiece and
tool).
2.
Main switch with low voltage release
In order to disconnect the electrical parts of the drilling and milling machine safely from the
mains, we have provided a main switch with low voltage release besides the mains lead with
plug. This under voltage release prevents the drive motor from coming on after a power cut
and so excludes the danger of the work spindle moving unexpectedly.
3.
Emergency
OFF
switch
This enables a quick curtailment of dangerous movements, in particular when using devices for
CNC.
4.
Overload protection
This device has been developed to protect the drive motor and it must be noted that after the
motor has been turned off (by hand or automatically), because of overloading, a short pause of
1-3 seconds must be observed before turning the machine on again so that the relay of the
electrical parts can re-establish the closed circuit condition.
5.
Security machine cabin
The cabin has a door which, when closed, activates a limit switch. The feed motors can only be
put into motion on the axis independently by means of the CNC controls, when the door is
closed.
When the door is open the motor is switched to idle whereby manual operation is still possible.
The main spindle can be switched on whether the door is open or closed.
It is forbidden to remove the door limit switch or to put it out of action
as this could lead to serious danger to the machine operator and
cause severe accidents.
Summary of Contents for F1410 LF
