background image

 

 

 

connecting line emphatically might cause damage to it. 

9.

 

Cut off power and the connecting line immediately and contact the after-sales service center if 
the  product  or  the  connecting  line  is  damaged  for  some  reason.  Continuing  using  without 
maintaining might cause smoking or off-odor. 

10.

 

Do  not  hang  on  the  product,  which  might  cause  the  product  to  fall  or  injure  persons.  Take 
caution with children near the product. 

11.

 

Please cut off power for safety if not using the product for a prolonged period. 

12.

 

Do not let the connecting line get squeezed by the wall or buckle, pull or twine the connecting 
line. 

13.

 

Make sure the power and the connecting line are cut off when moving the product. 

14.

 

Keep the product from collisions, which might cause equipment failure. 

FCC RF Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. 
This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular 
installation. 
If this equipment causes harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures. 

o

 

Reorient or relocate the receiving antenna. 

o

 

Increase the space between the equipment and receiver. 

o

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 

o

 

Only a shielded interface cable should be used. 

Finally, any changes or modifications to the equipment by the user not expressly approved by the 
grantee or manufacturer could void the user's authority to operate such equipment. 

Doc Compliance Notice 

This digital apparatus does not exceed the Class A limit for radio noise emissions from digital 
apparatus set out in the radio interference regulation of Canadian Department of Communications. 

Summary of Contents for WBXML32RS



















Reviews: