background image

 

May 2, 2011

MAINTAINING THE JACE-700

Status

28

Part Number 11694  Rev 1.6

JACE-700

 

MOUNTING AND WIRING GUIDE

|

Status

The green “STATUS” LED is located on the cover. On the main board, it is also the 
green “SYSOK” LED next to the “HBEAT” LED—both are found near the Ethernet 
connector housing. The status LED should remain lit whenever the controller is 

powered

, or else be blinking during the boot sequence. If the status LED 

does not 

light

 while power is applied, contact System Engineering for technical support.

Heartbeat

The yellow heartbeat “HBEAT” LED is located on the cover, as well as on the main 
board next to the “SYSOK” Status LED. The heartbeat LED blinks about once per 
second. If the heartbeat LED stays 

on constantly

does not light

, or blinks 

very 

fast

 (more than once per second), contact System Engineering for technical support.

Debug

The yellow “DEBUG” LED is located on the main board near the Ethernet connector 
housing, and remains lit whenever the controller has been rebooted with the “serial 
mode select” jumper in the “serial shell” position (see 

Figure 5

 on page 14). This 

indicates that the DB-9 

RS-232

 port is operating in serial shell mode.

USB

Three yellow LEDs “LD1”, “LD2”, and “LD3” are located together on the upper left 
area on the main board, in the option slot 2 area. These LEDs indicate USB hub and 
port (1 and 2) activity, respectively. These LEDs will not be easily visible if an option 
card is installed in the upper (Slot 2) option slot.

Ethernet Ports

Two LEDs for each of the two LAN ports are provided on the back of the metal LAN 
connector housing, and operate as follows. 

The left-side 

green

 “activity” LED indicates activity on that port as follows:

Off 

— No Ethernet link is made

On 

— Ethernet link is present, but no activity on the LAN

Blinking 

— Ethernet link is present with data activity on the LAN.

The right-side 

yellow

 “speed” LED indicates Ethernet connection speed, as either:

Off 

— “Fast Ethernet” / “Ethernet” (100 Mbps /10Mbps).

On 

— “Gigabit Ethernet” speed (1000 Mbps).

Maintaining the JACE-700

This section provides information on the following topics:

Cleaning

Required NiMH Battery Maintenance

Replacement Parts

Replacing the JACE-700

Returning a Defective Unit

Summary of Contents for JACE-700





































Reviews: