background image

H49.0.01.6C-05_VWR 

Operating Manual TD 121  

          page 9 of 10 

 

 

 

 

10 Warranty 

VWR International 

warrants that this product will be free from defects in material and workmanship for a period 

of two (2) years from date of purchase. If a defect is present, VWR will, at its option, repair, replace, or refund the 
purchase price of this product at no charge to you, provided it is returned during the warranty period. This warranty 
does not apply if the product has been damaged by accident, abuse, misuse, or misapplication, or from ordinary 
wear and tear. 
For your protection, items being returned must be insured against possible damage or loss. This warranty shall be 
limited to the replacement of defective products. IT IS EXPRESSLY AGREED THAT THIS WARRANTY WILL BE 
IN LIEU OF ALL WARRANTIES OF FITNESS AND IN LIEU OF THE WARRANTY OF MERCHANTABILITY. 

11 Equipment disposal                    

 

 

 
This equipment is marked with the crossed out wheeled bin symbol to indicate that this equipment must not be 
disposed of with unsorted waste. 
Instead it's your responsibility to correctly dispose of your equipment at lifecycle -end by handling it over to an 
authorized facility for separate collection and recycling. It's also your responsibility to decontaminate the equipment 
in case of biological, chemical and/or radiological contamination, so as to protect from health hazards the persons 
involved in the disposal and recycling of the equipment. 
For more information about where you can drop off your waste of equipment, please contact your local dealer from 
whom you originally purchased this equipment. 
 
By doing so, you will help to conserve natural and environmental resources and you will ensure that your equipment 
is recycled in a manner that protects human health.  
 
Thank you   

 

Summary of Contents for TD 121











Reviews: