scanner on the white area of the White Balance Calibration paper
provided.
3.
Press and hold the [JPG/PDF] button. While holding the [JPG/PDF]
button, press the [POWER] button and then release both buttons to
enter into auto-calibration mode. SD symbol
will flash and then stop.
“GREEN” and “RED” LED light will turn on.
4.
Do not move the scanner. Wait until the “RED” LED turns off. “GREEN”
LED will stay on.
5.
With only the “GREEN” LED light on, start scanning the white paper by
sliding the scanner across the paper until the “GREEN” LED light turns
off. (Slide the scanner backwards if necessary).
6.
Press and hold the [POWER] button to power off the scanner.
Calibration is complete.
5.8 How to scan
NOTE
: To scan, make sure your scanner is not connected to the computer.
1. Turn on scanner by pressing the [Power/Scan] button for 2 seconds.
2. Hold the document firmly with one hand on a flat surface.
3. Place the scanner on the edge of the paper approximately 5/8 to 3/4 of an inch
onto the page to ensure the whole document can be scanned. Make sure to keep
the scanning area in between the scanning width indicators marked on the side of
the scanner.
4. Hold the scanner flat against the material and then press the [SCAN] button once.
5. Slide the scanner slowly, keeping your hand stable to get the best quality picture.
6. Press the [SCAN] button again to stop scanning.
6. Viewing your scans
1. Connect your scanner to your computer and then turn on your scanner.
2. Your computer should recognize the scanner as a “Removable Disk.”
Click “Open folder to view files” to view and import scans.
Note:
If the Removable Device Window did not launch automatically, go to your “My
Computer” and find the device under Removable Storage.
7. Specifications
Image sensor
Color Contact Image Sensor
Number of sensor
5136 dots(1st~5104 dots available)
Resolution
Low resolution : 300 dpi(default)
Medium resolution: 600 dpi
High resolution: 900 dpi
Maximum scanning
speed for Letter size
document
Color High resolution
Color Medium resolution
Color Low resolution
12 Seconds
8.0 Seconds
3.0 Seconds
Capacity (Based on 1GB
microSD card.Scan Letter
size file, the quantity of scans
vary depending on the
content complexity)
900dpi color
600dpi mono
300dpi color
110 Photos(Min.)
250 Photos(Min.)
850 Photos(Min.)
Scan width
8.27"
Scan length (max.)
300dpi: 98", 600dpi: 45", 900dpi: 35”
File format
JPG(default) / PDF
LCD
Scanning status display
Auto Power Off
3 Minutes
USB Port
USB 2.0 high speed
External memory
microSD/microSDHC Card
Standard Battery
2XAA alkaline batteries
8. Computer system minimum requirement
Operating System
Windows® XP, Windows® Vista™, Windows® 7
and Mac OS® 10.4 or above
(direct plug-in, driver installation not required)
CPU
Pentium III or above
RAM
256MB
Interface
USB port
9. Troubleshooting
Problem
Cause
Solution
Cannot turn on the
scanner
1. Low battery power.
2. Battery not inserted
properly
Replace or install the
battery correctly
Pictures cannot be
saved when you are
scanning them
1. microSD card has
not been installed
2. Memory is full
3. The microSD card
has not been
formatted properly
1. Install microSD card
2. Download the pictures from
the scanner to the computer
to create storage space
3. Reformat your microSD card.
Please refer to section 5.3
Computer does not
recognize your scanner
when connected. (You
cannot find removable
disk)
Connection failure.
Make sure all cable
connections are secured.
Restart the computer if
necessary
The battery life is very
short
Use wrong type of
battery
Replace with new
2x AA alkaline batteries
Blurry images
The lens of scanner is
dirty
Clean the lens with soft
dry cloth
ERR. LED is on after
powering on scanner
Sensor off-set
Recalibrate the scanner. Refer
to Section 5.7
ERR. LED is on when
scanning a document
Scanning speed is too
fast
Press the Power/Scan button to
reset your scan. Scan the
document again.
Black images/ Black or
White vertical lines
1. Scanner sensor
protective glass is
dirty
2. Calibration data is
off-set
1. Clean the sensor’s protective
glass with clean and soft dry
cloth.
2. Recalibrate the scanner.
Refer to Section 5.7
10. ABBYY® OCR Software
(Optional, not required to install to operate scanner)
Compatible with Windows® XP, Windows® Vista™, Windows® 7
To access the software User’s Manual go to the Help menu for instructions on how
to use the OCR software application:
1. Load and open the ABBYY software.
2. Press the “F1” key located on your keyboard to launch the “Help” menu from the
software.
3. OR, locate the ABBYY icon found next to the Time indicator on your computer’s
taskbar and then right click on the icon to access the “Help” menu.
FCC (Federal Communications Commission)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
this device must accept any interference received, including
interference thay may cause undesired operation.
Windows® XP, Windows® Vista™, Windows® 7 are registered trademarks of Microsoft Corporation.
Mac OS® 10.4 is a registered trademark of Apple Inc.
ABBYY® is a registered trademark of ABBYY Software Ltd.
microSD and microSDHC logo is a trademark of SD-3C, LLC.
All trademarks are the property of their respective owner.
PDS-ST410A-VP-BX3_Manual_12-0305
AM-N410AFVC-GB-VPS-1
