Vulcan-Hart GR Series Service Manual Download Page 10

Page: 10 / 56

REMOVAL AND REPLACEMENT OF PARTS

COVERS AND PANELS

Disconnect the

electrical power to the machine and
follow lockout / tagout procedures.

Control Panel

Remove screws at top of control panel, and
rotate panel downward.

COMPUTER CONTROL, C MODEL

Fig. 6

Disconnect wiring harness, then lift off panel.

NOTE:

The cooking control, control box, interface

board, and wiring harness are now accessible.

Reverse procedure to install.

Basket Lift Covers

Shut off the gas

before servicing the unit and follow
lockout / tagout procedures.

All gas joints disturbed during

servicing must be checked for leaks. Check with a
soap and water solution (bubbles). Do not use an open
flame.

NOTE:

This procedure applies to fryers with

automatic basket lift option only.

Remove basket assembly lift arms from support
rods.

Remove screws securing upper cover to flue
wrap.

Fig. 7

Lift upper cover over support rods, and
place cover to the side.

Remove screws securing lower cover to motor
mounting base.

Fig. 8

Reverse procedure to install.

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - REMOVAL AND REPLACEMENT

OF PARTS

F35660

Rev. A (0717)

Page 10 of

Summary of Contents for GR Series

























































Search results

Summary of Contents for GR Series

Reviews:

Related manuals for GR Series

Brands by name

Popular brands

Vulcan-Hart GR Series, Service Manual

Search results

Summary of Contents for GR Series

Reviews:

Related manuals for GR Series

Brands by name

Popular brands