background image

— 2 —

INSTALLATION

Before installing the fryer, verify that the electrical service agrees with the specifications on the fryer
data plate which is located on the inside of the door panel.  If the supply and equipment requirements
do not agree, do not proceed with the installation.  Contact your dealer or Vulcan-Hart Company
immediately.

UNPACKING

This fryer was carefully inspected before leaving the factory. The transportation company assumes full
responsibility for safe delivery upon acceptance of the shipment.

Immediately after unpacking the fryer, check for the following items:

• Manual and warranty (packaged in clear plastic bag)

• Clean Out Rod

• Drain Extension

• Legs

• Tank Brush

• Crumb Rack

Installation, Operation and Care of

MODEL 1ER SERIES ELECTRIC FRYERS

PLEASE KEEP THIS MANUAL FOR FUTURE USE

GENERAL

Vulcan 1ER Series Electric Fryers are produced with quality workmanship and material. Proper
installation, usage and maintenance of your fryer will result in many years of satisfactory performance.

It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions
provided.

Vulcan 1ER  Series Electric Fryers are available in various sizes, with an array of features and options
for a range of commercial fryer applications.

The 1ERD models  have  solid state controls, melt cycles and two timers. The 1ERC Fryers have
microprocessor computer controls, melt cycles and  multiple timers.

Width

Fry Compound

Model

KW

Inches / cm

Voltage

Lb / kg

1ER50D/1ER50C

17

15

1

/

2

  (394 mm)

208/240 3 Ph

45-50 (20-23 kg)

1ER85D/1ER85C

24

21 (533 mm)

208/240 3 Ph

85-100 (39-41 kg)

FIELD-INSTALLED ACCESSORIES

• Casters
• Flanged Feet
• Single Baskets
• Twin Baskets

• Tri-Baskets
• Tank Cover
• Removable Splash Guard
• GRO15 Frymate

Summary of Contents for 1ER50C





















Reviews: