Specifications are subject to change without notice.
© 2018 VTech Communications, Inc. All rights reserved.
02/18. VM352-2_QSG_V
2
.
Document order number: 96-011935-0
2
0-100
Basic operation -
Parent unit
Adjust speaker volume
Press
or
to adjust your parent unit
speaker volume. It determines the volume of sound
transmitted from your baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold
TALK
and speak to your parent unit.
Your voice is transmitted to the baby unit.
Turn off the parent unit
Press and hold
POWER
to power off your parent unit.
Basic operation -
Baby unit
Adjust speaker volume
Press
+ VOLUME -
to adjust your baby unit
speaker volume. It determines the lullaby volume
and talkback volume transmitted from your parent
unit.
Turn off the baby unit
Slide the
ON/OFF
switch to
OFF
to power off
your baby unit.
Lullaby
Press / to play lullaby on the baby units.
Press
to play the next lullaby.
Press / again to stop the lullaby.
•
•
Overview -
Parent unit
Overview -
Baby unit
Night vision
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby
unit
(optional)
OR
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
NOTES
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.
You can tighten the other screw in
the top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
You can maximize your baby unit’s viewing angles by tilting the
wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket. Tighten the screw into the
threaded socket at the bottom to secure the
baby unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Sound activation
When the baby unit detects no sound, the parent unit screen
stays off to save power. Once a sound is detected, the
parent unit screen turns on automatically. It will then turn off
again after 50 seconds of no sound detection.
Sound-activated Screen
On
Off
ē
63
ē
ē
63
ē
63
ē
Press and hold
63
ē
POWER
TALK
Zoom
Microphone
LED lights
Arrow keys
MENU / SELECT
VIEW / LCD ON/OFF
Volume
Stand
Power jack
Speaker
Battery compartment
cover
Antenna
63
ē
Turn off the screen
Press and hold
LCD ON/OFF
to switch off the screen.
You can still hear sound from the selected baby unit.
LCD is turning off...
Press any keys on the parent unit to turn on the
screen again.
•
TIP
Long press
Use the menu
Press
MENU/SELECT
to enter the menu, choose
a menu item, or save a setting. You can use
the parent unit menu for the advanced settings
or operations, such as to play or stop the baby
unit lullaby, or to adjust the baby unit sound
sensitivity.
While in the menu:
Press or to scroll up or down.
Press to select an item.
Press to return to the main menu or idle
screen.
•
•
•
Alert Tone
Low Battery Tone
No Link Alert
Sound alert in split-view
6U]KXOTMULL
6U]KXOTMULL
Long press
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When the
baby unit detects low light levels, the infrared LEDs
turn on automatically. The images from this baby
unit are in black and white, and appears on
screen.
NOTES
It is normal if you see a short white glare on your parent
unit screen as the baby unit is adapting to the dark
environment.
When the infrared LEDs are on, the images are in black
and white. This is normal.
TIP
Depending on the surroundings and other interfering
factors, like lightings, objects, colors and backgrounds,
the display resolution may vary. Adjust the baby unit’s
angle, or place the baby unit at a higher level to prevent
glare and blurry display.
•
•
•
Infrared LEDs
Light sensor
Camera
ON/OFF LED Light
Play/Stop
Microphone
Skip
Temperature
sensor
ON/OFF switch
+
VOLUME
-
Speaker
Threaded socket
Power Jack
