Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions
.
This manual has instructions on how to
set up and register your new sensor. For
instructions on sensor settings, see the
user’s manual that came with your telephone
base.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Motion Sensor overview
1 – Screw cover
Slide to open or close the screw cover
to reveal the battery compartment
case and
PAIRING
button.
2 – Back cover
3 – LED light
Briefly flashes red when the sensor is
first powered on.
Flash red once, when motion is
detected.
Flashes green when the sensor is in
registration mode.
4 – Motion detector
5 – PAIRING button
Press and hold to enter the
registration mode.
6 – Battery compartment case
•
•
•
•
•
Before use
Open the battery compartment case
Slide to open the screw cover and unscrew
the screw until the battery compartment
case is separable from the back cover.
Separate the battery compartment case
from the back cover.
Install Motion Sensor Battery
NOTES
Use only CR123A Lithium Battery.
When inserting battery, ensure polarities are
correct.
For proper operation, use battery within the following
temperature range: 0°F (-18°C) and 130°F (49°C).
Pull the ribbon tightly across the battery
compartment.
Insert the battery into the battery
compartment.
Add and register a sensor
You need to register your new
VC7003A
Contact
Sensor to your
VC7151-102A/VC7151-202A/
VC7151-302A
telephone system.
Register a Motion Sensor:
If you have just inserted the battery, wait
for the red LED to stop flashing.
Press and hold
/HANDSET LOCATOR
on
the telephone base for about 4 seconds until
the
IN USE
light turns on. The telephone
base shows
Registering... Please wait
.
1.
2.
•
•
•
1.
2.
1.
2.
Use a narrow pointed object such as a
pen to press and hold the
PAIRING
button
on the Motion Sensor, until the LED light
at the front side flashes green. The sensor
is now registering to the telephone base.
The registration process takes about 90
seconds to complete. When this registration
process completes, the green LED light
on the sensor will remain steadily on for
approximately two seconds then, will turn off.
If registration fails, remove battery from the sensor
and wait for a few seconds. Then, re-install
battery and wait until the red LED stops flashing.
After that, begin registration process again.
NOTES
If you are going to mount the sensor with screws or
mounting bracket, the back cover has to be mounted
before you assemble the battery compartment case
back to it (see
Mount the sensor
).
Replacing a sensor
If you have purchased this new
VC7003A
accessory sensor to replace an old sensor, follow
the instructions to deregister your old sensor.
VC7151-102A/VC7151-202A/VC7151-302A
telephone system can support up to 30 sensors.
To replace a sensor, deregister the registered
sensor first, and then register this new sensor
to the telephone base.
To deregister a sensor on VC7151-102A/
VC7151-202A/VC7151-302A telephone system:
1. Press
MENU
when the phone is not in use.
2. Enter the code
*33734#
to access the
DEREGISTER
menu.
3. Press or on the handset, or
CALLS
/
or
PHONEBOOK
/ to scroll to
Single
sensor
, and then press
SELECT
.
4. Press or on the handset, or
CALLS
/
or
PHONEBOOK
/ to scroll to the sensor
to be deregistered, and then press
SELECT
.
5. Press
YES
to confirm the deregistration.
The telephone base shows
Motion X is
deregistered
and you hear a beep when the
deregistration process completes.
3.
•
Motion detection
The Motion Sensor detects motion with
one-minute cool off time. Once motion is
detected, the sensor will start detecting
motions again only after one minute.
The Motion Sensor is more sensitive in
detecting motions crossing the space in front
of the sensor than that moving towards the
sensor.
The Motion Sensor can detect motion
occurring at distances up to
40 feet
(12 meters)
when it is mounted at a height
of
7.9 feet (2.4 meters)
.
It is recommended to mount the sensor at the
height between
6.2 feet (1.9 meters)
and
7.5 feet
(2.3 meters)
for optimal detection coverage.
For motion detection of babies or pets:
If you use the Motion Sensor only to detect
the motion of babies or pets, you can mount
the sensor at a lower position to shorten
the minimum distance before reaching the
detection area. It is recommended to mount
it at the height
3.3 feet (1 meters)
for optimal
detection of babies and pets.
NOTE
The numerical values in the illustrations are for
conceptual reference only. The actual angles
and distances may vary upon the change in the
mounted height of the sensor.
•
Check the sensor before use
1. Place the sensor about
3.3 feet (1 meter)
from the telephone base.
2. Waive your hand or walk across the area
in front of the sensor.
You will receive alerts at your telephone
base. Refer to the Installation guide or
user’s manual of your telephone base
for the sensor alerts.
The LED light on the Motion Sensor will
flash red once.
NOTE
Once motion is detected, the sensor will only
start to detect motion again after one minute.
When you have received alerts already, you will
only receive alerts again for motion detected
after one minute.
•
•
•
Test the sensor signal strength
You can mount the Motion Sensor at a
location where family members or unwanted
visitors are likely to be coming and going.
1. Take the sensor to the desired mounting
location and then, hold it at the desired
height (Refer to
Motion detection
section). Use adhesive tape to hold the
sensor temporarily in place.
2. Enter the
Check signal
mode under the
Sensor setup
menu at your handset to
test the sensor signal strength.
3. Waive your hand or walk across the area
in front of the sensor again and check
whether a good signal is received at your
telephone base.
NOTES
Once motion is detected, the sensor will only
start to detect motion again after one minute.
When you have received alerts already, you will
only receive alerts again for motion detected
after one minute.
If there is no alert received when you walk
across the area in front of the sensor, move
your telephone base closer to the mounting
location or move the sensor closer to the
respective product.
Depending on surroundings and obstructing
factors, like walls or cabinets, the sensor may
not transmit to the telephone base properly.
•
•
•
VC7003A
Accessory
Wire-Free Motion Sensor
for use with
VC7151-102A/
VC7151-202A/
VC7151-302A
User’s manual
Motion Sensor
Mounting bracket
on mounting base
with screw
CR123A
Lithium battery
Mount the sensor
NOTES
This sensor must be mounted vertically on wall. Do not mount the Motion Sensor in a horizontal
orientation, or flat on the ceiling.
Make sure the mounting surface is clean. A textured surface or any imperfections to a smooth surface
can keep the mounting tape from making a strong bond.
This device detects or performs better when provided with a constant and stable environment.
Avoid placing the sensor at a location which faces direct sunlight, or exposes to areas that may change
temperature rapidly, or where there are air ducts or substantial airflows.
The recommended mounting height for motion detection of adults is between
6.2 feet (1.9 meters)
and
7.5 feet (2.3 meters)
, and that for babies or pets is about
3.3 feet (1 meter)
.
If you drill the holes into an object other than a stud, insert the screw anchors into the holes and tap
gently on the ends with a hammer until the screw anchors are flush with the wall or ceiling.
TIP
You can choose to mount the sensor with the mounting tape first. Remove the mounting tape and use
screws later if you decide to mount it at that location for long term.
•
•
•
•
•
•
User’s
manual
User’s manual
2
3
4
1
Screw for
mounting
brackets x 2
Screw for
back cover x 3
Mount on the wall - with fixed angle
Mount on the wall - with rotated detection angle
1
2
3
5
P
P
a
b
i
k
l
m
c
d
e
f
g
h
j
n
o
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
(Optional)
Insert screw
anchors if
necessary.
Anchor for
back cover x 3
Anchor for
mounting
brackets x 2
Double-sided
mounting tape
Mount with tape
Mount on the wall - with fixed angle
Mount with screws
4
5
2
3
1
Drill a hole
here.
Up to 34.4 feet
(10.5 meters)
Side view
Detection
area
78
o
Top view
Shooting area
19.7 inches
60 degrees
22.8 inches
Shooting area
19.7
inches
50 degrees
18.3
inches
63 inches
87
o
Detection area
1.3 feet
(0.4 meter)
10
o
Height: 6.9 feet (2.1 meters)
Height: 6.9 feet (2.1 meters)
Side view
Detection
area
78
o
Top view
87
o
Detection area
0.7 feet
(0.2 meter)
10
o
Height: 3.3 feet (1 meter)
Up to 16.4 feet
(5 meters)
Height: 3.3 feet (1 meter)
TIP
You can rotate the sensor 45 degree, and then mount the sensor next to the corner of wall for optimal
detection coverage.
•
NOTE
This product requires professional installation.
•
2
1
This screw should only
be fully secured after you
adjusted the angle.
Unscrew first.
4
5
6
7
Tighten the screws after
you slided the sensor
over them.
(Optional)
Insert screw
anchors if
necessary.
Tighten
the scew.
Tighten
the scew.
Tighten
the scew.
1
2
