Battery
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire. Check
with local waste management codes for
special disposal instructions.
Do not open or mutilate the battery.
Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin.
The electrolyte may be toxic if swallowed.
Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
Charge the battery provided with or identified
for use with this product only in accordance
with the instructions and limitations specified
in this manual.
Precautions for users of implanted
cardiac pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless telephones and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least six
inches from the pacemaker.
Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
Should use the wireless telephone at the ear
opposite the pacemaker.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless telephones.
About cordless telephones
Privacy:
The same features that make a
cordless telephone convenient create some
limitations. Telephone calls are transmitted
between the telephone base and the
cordless handset by radio waves, so there
is a possibility that the cordless telephone
conversations could be intercepted by
radio receiving equipment within range
of the cordless handset. For this reason,
you should not think of cordless telephone
•
•
•
•
•
•
•
•
•
conversations as being as private as those
on corded telephones.
Electrical power:
The telephone base of
this cordless telephone must be connected
to a working electrical outlet. The electrical
outlet should not be controlled by a wall
switch. Calls cannot be made from the
cordless handset if the telephone base is
unplugged, switched off or if the electrical
power is interrupted.
Potential TV interference:
Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference, do
not place the telephone base of the cordless
telephone near or on top of a TV or VCR.
If interference is experienced, moving the
cordless telephone farther away from the
TV or VCR often reduces or eliminates the
interference.
Rechargeable batteries:
Exercise care in
handling batteries in order not to create a
short circuit with conducting material such
as rings, bracelets and keys. The battery or
conductor may overheat and cause harm.
Observe proper polarity between the battery
and the battery charger.
Nickel-metal hydride rechargeable
batteries:
Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury
The RBRC
®
seal
The RBRC
®
seal on the nickel-metal hydride battery
indicates that VTech Communications, Inc. is
voluntarily participating in an industry program to
collect and recycle these batteries at the end of their
useful lives, when taken out of service within the
United States and Canada.
The RBRC
®
program provides a convenient
alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which
may be illegal in your area.
VTech’s participation in RBRC
®
makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC
®
program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERY
TM
for information on Ni-MH
battery recycling and disposal bans/restrictions in
your area. VTech’s involvement in this program is
•
•
•
•
part of its commitment to protecting our environment
and conserving natural resources.
RBRC
®
is a registered trademark
of Rechargeable Battery Recycling
Corporation.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device
under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product.
This product has been tested and found to comply
with the FCC criteria. The base shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately 8 in (20
•
•
•
•
cm) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC
rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this
equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service
provider upon request.
The plug and jack used to connect this equipment
to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with
this product. It is designed to be connected to a
compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to
a single line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to
determine how many devices you may connect to
your telephone line and still have them ring when you
are called. The REN for this product is encoded as
the 6th and 7th characters following the US: in the
product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should
be five (5.0) or less. For more information, please
contact your telephone service provider.
This equipment may not be used with Party Lines.
If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the
connection of this equipment does not disable your
alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it must be
unplugged from the modular jack until the problem
has been corrected. Repairs to this telephone
equipment can only be made by the manufacturer or
its authorized agents. For repair procedures, follow
the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone
network, the telephone service provider may
temporarily discontinue your telephone service. The
telephone service provider is required to notify you
before interrupting service. If advance notice is not
practical, you will be notified as soon as possible.
You will be given the opportunity to correct the
problem and the telephone service provider is
required to inform you of your right to file a complaint
with the FCC. Your telephone service provider may
make changes in its facilities, equipment, operation,
or procedures that could affect the proper functioning
of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless
handset, it is hearing aid compatible.
If this product has memory dialing locations, you may
choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you
do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for
the call before hanging up.
Perform such activities in off-peak hours, such as
early morning or late evening.
Industry Canada
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Privacy of communications may not be ensured
when using this telephone.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this
terminal equipment is 0.1. The REN is an indication
of the maximum number of devices allowed to be
connected to a telephone interface. The termination
on an interface may consist of any combination of
devices subject only to the requirement that the sum
of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada
technical specifications.
RF radiation exposure statement
The handset complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The base should be installed and
operated with a minimum distance of 8 in (20 cm)
between the handset
and all persons’ body. Use of
other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with
any other antenna or transmitter. This equipment
complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
California Energy Commission
battery charging testing instructions
This telephone is set up to comply with the
energy-conserving standards right out of the box.
These instructions are intended for California Energy
Commission (CEC) compliance testing only.
When the CEC battery charging testing mode is
activated, all telephone functions, except battery
charging, will be disabled.
When first purchased and properly installed for charging
(see
Install the battery
), put the handset on the charger
to charge. The CEC battery charging testing mode is
activated while charging.
If you have registered the handset to a telephone base,
below are the testing instructions.
To activate the CEC battery charging testing mode:
Unplug the telephone base power adapter from
the wall outlet. Make sure all handsets are plugged
with charged batteries before proceeding.
While you press and hold
/FIND HANDSET
, plug
the telephone base power adapter back to the wall
outlet.
After about 20 seconds, After about 20 seconds,
when the
/HOME
light starts flashing, release
/FIND HANDSET
and then press it again within
2 seconds.
When the phone successfully enters the energy
conserving mode, all cordless handset screens
display
To register HS...
and
see manual
. When the
phone fails to enter the CEC battery charging testing
mode, repeat Step 1 through Step 3 above.
The telephone base will be powered up as normal
if you fail to press
/FIND HANDSET
within
2 seconds in Step 3.
To deactivate the CEC battery charging testing mode:
Unplug the telephone base power adapter from the
wall outlet, then plug it back in. Then the telephone
base is powered up as normal.
Register your handsets back to the telephone
base. Refer to the
Add and register a handset
section.
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures
corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez
votre téléphone :
Lisez et comprenez bien toutes les instructions.
Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
Débranchez ce téléphone de la prise murale
1.
2.
3.
•
1.
2.
1.
2.
3.
avant de le nettoyer. N’utilisez pas de nettoyeurs
liquides ni en aérosol. N’utilisez qu’un chiffon
doux et légèrement humecté.
N’utilisez pas ce produit près de l’eau, tel que
près d’un bain, d’un lavabo, d’un évier de
cuisine, d’un bac de lavage ou d’une piscine, ou
dans un sous-sol humide ou sous la douche.
Ne déposez pas ce téléphone sur un chariot,
support ou table chancelants. L’appareil pourrait
tomber et être sérieusement endommagé.
Le boîtier de l’appareil est doté de fentes et
d’ouvertures d’aération situées à l’arrière ou en
dessous. Afin d’empêcher la surchauffe, ces
ouvertures ne doivent pas être obstruées en
plaçant l’appareil sur un lit, divan, tapis ou autre
surface similaires. Ne placez pas cet appareil
à proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas
dans une unité murale ou un cabinet fermé qui
ne possède pas d’aération adéquate.
Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes de
l’appareil. Si vous ne connaissez pas le voltage
de votre maison, consultez votre marchand ou
votre fournisseur d’électricité.
Ne déposez rien sur le cordon d’alimentation.
Installez cet appareil dans un endroit sécuritaire,
là où personne ne pourra trébucher sur la
ligne d’alimentation ni le cordon téléphonique
modulaire.
N’insérez jamais d’objets à travers les fentes
et ouvertures de cet appareil, car ils pourraient
toucher à des points de tension dangereux ou
court-circuiter des pièces, ce qui constituerait un
risque d’incendie ou d’électrocution. N’échappez
pas de liquides dans l’appareil.
Afin de réduire les risques d’électrocution, ne
démontez pas l’appareil, mais apportez-le plutôt
à un centre de service qualifié s’il doit être
réparé. En enlevant le couvercle, vous vous
exposez à des tensions dangereuses ou autres
dangers similaires. Un remontage inadéquat
peut être à l’origine d’une électrocution lors
d’une utilisation ultérieure de l’appareil.
Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.
Ne surchargez pas les prises de courant et les
rallonges.
Débranchez cet appareil de la prise de courant
et communiquez avec le département de
service à la clientèle de VTech dans les cas
suivants:
Lorsque le cordon d’alimentation est
endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source
d’humidité telle que la pluie ou l’eau.
4.
5.
6.
7.
8.
9.
10.
11.
12.
•
•
•
Si le produit ne fonctionne pas
normalement en respectant les instructions
de fonctionnement. Réglez uniquement les
commandes indiquées dans le les instructions
de fonctionnement. Les réglages incorrects
des autres commandes pourraient provoquer
un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé
afin de rétablir le fonctionnement normal de
l’appareil.
Si le produit a été échappé et que le socle
et/ou le combiné a été endommagé.
Si le produit affiche une nette diminution de
sa performance.
Évitez d’utiliser un téléphone (autre qu’un sans
fil) pendant un orage. Les éclairs peuvent être à
l’origine d’une électrocution.
N’utilisez pas le téléphone pour rapporter une
fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être
provoquée lorsque l’adaptateur est branché à
une prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un événement
commun associé à la fermeture d’un circuit
électrique. L’utilisateur ne devrait pas brancher
le téléphone à une prise de courant, et ne
devrait pas déposer le combiné chargé sur le
socle, si le téléphone se trouve à proximité d’un
endroit comportant des concentrations de gaz
inflammables, à moins que la ventilation soit
adéquate. Une flammèche dans un tel endroit
pourrait provoquer un incendie ou une explosion.
De tels environnements peuvent comprendre:
des endroits où l’on utilise de l’oxygène médical
sans ventilation adéquate; des gaz industriels
(dissolvants de nettoyage, des vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
Ne placez que le combiné de votre téléphone
près de votre oreille lorsqu’en mode de
conversation.
Ces adaptateurs ont été conçus pour être
orientés en position verticale ou montés au sol.
Les broches ne sont pas conçues pour maintenir
l’adaptateur en place si celui-ci est barnché dans
une prise au plafond ou sous une table/ armoire.
CONSERVEZ CES INSTRUCTIONS
Pile
MISE EN GARDE : N’utilisez que la pile incluse.
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte
qui s’en échapperait est corrosif et pourrait causer
des brûlures ou des blessures aux yeux ou à la
peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles
afin d’éviter les courts-circuits provoqués par des
matériaux conducteurs.
Rechargez la pile incluse avec cet appareil, selon
•
•
•
•
13.
14.
15.
16.
•
•
•
•
les instructions et limites spécifiées dans ce guide
d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique uniquement
aux téléphones numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante, a mené
une évaluation pluridisciplinaire des interférences entre
les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Ils doivent tenir le téléphone sans fil à une distance
d’au moins six pouces du stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est en
marche.
Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un
téléphone sans fil à proximité de ceux-ci.
À
propos des téléphones sans fil
Alimentation électrique:
Les mêmes
caractéristiques qui constituent des avantages
pour les téléphones sans fil affichent également
des restrictions. Les appels téléphoniques sont
transmis entre le combiné sans fil et le socle par
le biais d’ondes radio ; il y a donc la possibilité que
vos conversations téléphoniques sans fil soient
interceptées par des équipements de réception
radio se trouvant dans la portée du combiné sans fil.
Pour cette raison, vous ne devez pas percevoir les
communications téléphoniques sans fil comme étant
aussi confidentielles.
Alimentation électrique:
Le socle de ce téléphone
sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être
contrôlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si
le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téléviseurs:
Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interférences aux
téléviseurs et aux magnétoscopes. Pour réduire ou
prévenir de telles interférences, ne placez pas le
socle du téléphone sans fil près ou sur un téléviseur
ou magnétoscope. S’il y a présence de parasites,
•
•
•
•
•
•
il est conseillé d’éloigner le téléphone sans fil du
téléviseur ou du magnétoscope afin de réduire
possiblement les interférences.
Piles rechargeables:
Manipulez les piles avec soin
afin de ne pas les court-circuiter avec des bagues,
bracelets ou clés. Les piles ou le conducteur peut
surchauffer et causer des blessures. Respectez la
polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables
à
l’hydrure
métallique de nickel:
Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez
pas et ne les percez pas. Tel que les autres piles
de ce type, elles pourraient dégager une matière
toxique qui peut causer des blessures corporelles
si elles sont brûlées ou percées.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided
in the sales package (“Product”) are free from
defects in material and workmanship, pursuant to the
following terms and conditions, when installed and
used normally and in accordance with the Product
operating instructions. This limited warranty extends
only to the Consumer for Products purchased and
used in the United States of America and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s authorized
service representative will repair or replace at
VTech’s option, without charge, a Materially Defective
Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to
replace the Product, we may replace it with a new or
refurbished Product of the same or similar design.
We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s
option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working
condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product
under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the
date the repaired or replacement Product is shipped to
•
•
you or (b) the time remaining on the original one-year
warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
Product to the extent that the problem
experienced is caused by signal conditions,
network reliability, or cable or antenna systems; or
Product to the extent that the problem is caused
by use with non-VTech accessories; or
Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible;
or
Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
Product returned without a valid proof of purchase
(see item 2 on the next page); or
Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the
risk of loss or damage during transit and transportation
and are responsible for delivery or handling charges
incurred in the transport of the Product(s) to the
service location. VTech will return repaired or replaced
Product under this limited warranty. Transportation,
delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product
in transit. If the Product failure is not covered by this
limited warranty, or proof of purchase does not meet
the terms of this limited warranty, VTech will notify you
and will request that you authorize the cost of repair
prior to any further repair activity. You must pay for the
cost of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
1.
2.
3.
4.
5.
6.
7.
8.
What must you return with the Product to get
warranty service?
Return the entire original package and contents
including the Product to the VTech service
location along with a description of the malfunction
or difficulty; and
Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modifications to this limited warranty and you
should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other
rights, which vary from state to state or province to
province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary
use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how
long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable
for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost
profits or revenue, inability to use the Product or
other associated equipment, the cost of substitute
equipment, and claims by third parties) resulting from
the use of this Product. Some states/provinces do
not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt
as proof of purchase.
1.
2.
3.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
DECT frequency: 1921.536-1928.448 MHz
Bluetooth frequency: 2402.000-2480.000MHz
Channels
DECT: 5
Bluetooth: 79
Nominal
effective
range
Maximum power allowed by FCC and IC.
Actual operating range may vary according
to environment conditions at the time of use.
Power
requirements
Handset: 2.4V 400mAH AAAx2 Ni-MH battery
Charger: 6V AC @ 300mA
Memory
Directory:
Home line: 200 memory locations, up to
30 digits and 15 characters
Each cell line: 1500 memory locations, up
to 30 digits and 15 characters
Caller ID log:
50 memory locations; up to 24 digits and
15 characters
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
Copyright © 2014 for VTech Communications, Inc.
All rights reserved. 06/14. DS6290_CIB_V2.0
Document order number: 91-007712-020-100
Designed to fit your home.
And your life.
The
Bluetooth
®
word mark and logos are owned by
Bluetooth SIG, Inc. and any use of such marks by VTech
Holdings Limited is under license. VTech Holdings Limited
is a member of Bluetooth SIG, Inc. Other trademarks and
trade names are those of their respective owners.