VTech CTM-A2415 Master User Manual Download | Manualshive

Page: 31 / 40

background image

EN - 31

English

Appendix

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found
to comply with the requirements for a Class
B digital device under Part 15 of the Federal
Communications Commission (FCC) rules.
These requirements are intended to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

Changes or modiﬁcations to this equipment
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This Class B digital apparatus complies with
Canadian ICES-003.

«
...
29
30
31
32
33
...
»

Summary of Contents for CTM-A2415









































Reviews:

No comments

Related manuals for CTM-A2415

Brand: Jacob Jensen Pages: 32

Brand: STARPLUS Pages: 294

Brand: TCL Pages: 18

PhoneEasy 331ph

Brand: Doro Pages: 2

Brand: Furuno Pages: 2

Brand: TIPTEL Pages: 28

Brand: Zte Pages: 15

Brand: Samsung Pages: 12

Brand: Samsung Pages: 41

Brand: Samsung Pages: 56

Brand: Samsung Pages: 65

Brand: Samsung Pages: 83

Brand: TransTel Communications Pages: 2

Brand: Doro Pages: 40

Brand: Gemini Pages: 16

Brand: brastel Pages: 17

Brand: Avaya Pages: 52

Brand: VTech Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands