background image

CENTERPOINTE BUTCHER BLOCK COUNTERTOPS

IMPORTANT INFORMATION ABOUT YOUR CENTERPOINTE COUNTERTOP 

BUTCHER BLOCK 

COUNTERTOP INSTALLATION

PRIOR TO INSTALL

•  Keep product in its packaging and away from humidity or direct heat until you are ready to install.
•  Allow your countertop to acclimate for 72 hours prior to installation. Sand and apply a  finish immediately after 

acclimating. (See pg. 2 for details).

•  Lightly sand all surfaces of your CenterPointe countertop with 120 grit sandpaper, in the direction of the wood 

grain, prior to applying finish.

•  All surfaces of the CenterPointe countertop must be finished. This includes top, bottom, edges and ends. 

Typical finish options include oil, wax, sealant, stain, urethanes, and acrylic. Apply finish according to finish 

manufacturer’s instructions.

DURING INSTALL

•  If  CenterPointe  butcher  block  countertops  are  installed  where  food  will  be  prepared,  a  food-safe  finish  is 

recommended.

•  Reapply finish to any areas that have been cut during installation.
•  DO NOT attach CenterPointe countertops to an existing countertop.
•  DO NOT glue CenterPointe countertops down to fix their position; allow for movement during humidity and 

temperature changes.

AFTER INSTALL

•  Do not place hot items directly on the surface. Contact with the wooden work surface may result in permanent damage.
•  Clean the countertop in accordance with the finish manufacturer’s instructions.  
•  Avoid leaving standing water on the countertop for a prolonged period of time.
•  DO NOT cut or chop on CenterPointe butcher block countertop, as it may cause scoring. Always use a chopping 

block.

•  If light scratches occur, sand the surface lightly with 120 grit sandpaper and re-apply finish.

TOOLS REQUIRED:

Measuring 

Tape

Pencil 

#10 Wood Screws

#10 Washers

Circular 

Saw

Drill

Set of 

Drill Bits 

Screw 

Driver

1

Masking

Tape

*How To Determine Screw Length
The appropriate length #10 screws and washers should be carefully chosen 

so the screw does not go all the way through the top, but the depth of 

penetration is enough to secure the butcher block countertop in place.
Butcher Block 3/4” Pilot Hole + Sub-Top Cabinet Base Thickness

Self-Adhering

Aluminum Flashing

Finish

Carpenter 

Square

Router

Silicone Sealant

& Gun

120 Grit 

Sandpaper

Type 

III

Glue

PVA 

Glue

Summary of Contents for CenterPointe BUTCHER BLOCK COUNTERTOP








Reviews: