Service
Vossloh-Schwabe Deutschland GmbH
P.O. Box 28 69
D-58478 Lüdenscheid, Germany
Phone: +49 (0)23 51/10 10
For further information please visit our website: www.vossloh-schwabe.com
ENGLISH
EN
Safety notes
!
The Blu2Light products may only be installed and commissioned by authorised specialists. Read
these instructions carefully before installing and commissioning the system. This is the only way to
ensure safe and correct handling. Keep this manual in a safe place so that it may be available at a
later date. Before any work is carried out on the equipment, it must be disconnected from the mains.
When used in IT power networks, a 2-pole fuse must be provided, which disconnects the device
from the mains on all poles. Carry out a condition test. The applicable safety and accident prevention
regulations must be observed. Improper opening of the products is not permitted, there is a danger to
life due to electrical voltage. Repairs may only be carried out by the manufacturer.
Bluetooth
®
wireless technology
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by Vossloh-Schwabe is under license. Other trademarks
and trade names are those of their respective owners.
We, Vossloh-Schwabe Deutschland GmbH, herewith confirm that these devices comply with the
basic requirements of the directive 2014/53 / EU and other relevant directives. The entire text of the
declaration of conformity can be obtained from the following address: Vossloh-Schwabe Deutschland
GmbH, Hohe Steinert 8, D-58509 Lüdenscheid
Attention 230 VAC
Make sure that they are de-energized and that the corresponding fuse is switched off and
secured. The mains voltage may only be switched on again after all switches/buttons and
covers have been fitted.
Installation
•
The 4-fold digital input module is intended for use in a standard flush-mounted box.
• First connect the push-button / switch to the Connect PB4 module via the push-in terminals
(T1, T2, T3, T4, COM).
• Pay attention to the correct polarity according to the connection markings!
• Assembly of the push-button cover.
• Switch on the power supply.
Observe correct polarity
Pay attention to the correct polarity of L and N
Installation instructions
• Only buttons or switches suitable for mains voltage may be connected to inputs T1/T2 and COM.
• The module must be placed inside the switch box and connected to the 230 VAC supply via a
terminal.
• Make sure that the polarity of L and N is correct.
Setup and operation
•
The Blu2Light devices are configured with the LiNA Connect app and can be operated via the
LiNA Touch app.
•
For the exact procedure for the configuration of the devices please refer to the instructions in the
LiNA Connect app or in the corresponding documentation.
• A tablet is required for setup, both tablets and smartphones can be used for operation. Both are
not included in the scope of delivery.
App operating mode and operating devices
LiNA Connect (configuration)
iOS
iPad
version 10 and higher
LiNA Touch (operation)
iOS
Android
Tablet
version 10 and higher
version 5.0 or higher
Smartphone
version 10 and higher
version 5.0 or higher
Technical Notes
Ref.-No. Connect PB4 186914
Communication: Blu2Light mesh network
Power supply: 220...240 V at 50...60 Hz
Power consumption: max. 0,5 W
Frequency range: 2402-2480 MHz
Output power: < 10 mW EIRP
Ambient temperature ta: 5-40 °C
Protection class: IP20
Protection class II
Housing diameter: 53 mm
Housing height: 22.5 mm
Housing: Polycarbonate, white
Weight 40 g
Push-in terminals: for flexible and rigid conductors with max. cross section 1.5 mm²
(L, N, COM, T1, T2, T3, T4)
Input T1, T2, T3, T4: max. 20 cm wire length per terminal
Schaltbild / Wiring diagram
