background image

 

VPI Industries, Inc. Limited Warranty 

VPI Industries, Inc. (VPI) warrants this unit against defects in materials and/or workmanship for 
three  (3)  years  from  the  date  of  purchase  by  the  original  retail  purchaser.  VPI’s  sole  obligation 
under this warranty is limited to the repair or replacement, at VPI’s option, of any part(s) found 
to  be  defective.  VPI’s  obligation  to  repair  or  replace  defective  parts  is  the  purchaser’s  sole  and 
exclusive  remedy,  and  VPI  shall  not  be  liable  for  any  direct  or  indirect  injury  and/or  property 
damage arising out of the use of the product or defect in or failure of the product.  

This warranty does not extend to any unit whose serial number has been defaced or altered. Any 
product  that  VPI  determines  causes  a  defect  or  malfunction  due  to  incorrect  installation, 
modification, misuse, or servicing by the purchaser, or service technician not authorized by VPI to 
perform  such  service  will  not  be  warranted.  This  warranty  does  not  cover  trivial  or  cosmetic 
defects that do not impair the unit’s normal function. 

VPI reserves the right to make changes in this product without assuming any obligation to install 
such change in any product previously manufactured. This warranty to repair or replace defective 
parts  is  in  lieu  of  all  other  express  or  implied  warranties  of  merchantability  or  fitness  for  a 
particular purpose. There are not warranties that extend beyond the description herein. 

Some states do not allow exclusion of implied warranties or limitation of incidental or 
consequential damages, so the above exclusion or limitations may not apply to you. This warranty 
gives you specific legal rights, and you may also have other rights that vary from state to state. 

 

Register your Product Online: 

http://vpiindustries.com/warranty/

 

 

 

 

 

Summary of Contents for Scout 2/JMW-9T













Reviews: