background image

 

VPI Industries, Inc. Limited Warranty 

VPI  Industries,  Inc.  (VPI)  warrants  this  unit  against  defects  in  materials  and/or 
workmanship  for  three  (3)  years  from  the  date  of  purchase  by  the  original  retail 
purchaser. VPI’s sole obligation under this warranty is limited to the repair or replacement, 
at VPI’s option, of any part(s) found to be defective. VPI’s obligation to repair or replace 
defective parts is the purchaser’s sole and exclusive remedy, and VPI shall not be liable for 
any direct or indirect injury and/or property damage arising out of the use of the product 
or defect in or failure of the product.  

This  warranty  does  not  extend  to  any  unit  whose  serial  number  has  been  defaced  or 
altered. Any product that VPI determines causes a defect or malfunction due to incorrect 
installation, modification, misuse, or servicing by the purchaser, or service technician not 
authorized by VPI to perform such service will not be warranted. This warranty does not 
cover trivial or cosmetic defects that do not impair the unit’s normal function. 

VPI reserves the right to make changes in this product without assuming any obligation to 
install  such  change  in  any  product  previously  manufactured.  This  warranty  to  repair  or 
replace  defective  parts  is  in  lieu  of  all  other  express  or  implied  warranties  of 
merchantability  or  fitness  for  a  particular  purpose.  There  are  not  warranties  that  extend 
beyond the description herein. 

Some  states  do  not  allow  exclusion  of  implied  warranties  or  limitation  of  incidental  or 
consequential damages, so the above exclusion or limitations may not apply to you. This 
warranty gives you specific legal rights, and you may also have other rights that vary from 
state to state.  

 

Register your Product Online: 

http://vpiindustries.com/warranty/

 

 

 

Summary of Contents for JMW-9 Scout Tonearm









Reviews: