background image

128-9317

7 of 16 

Page 7

 If the LED is flashing one time...pause...one time...pause...etc., then an 

intrusion attempt was made to the shock sensor, or an accessory triggering 

device that may have been added to the system.

 If the LED is flashing two times...pause...two times...pause...etc., then an 

intrusion attempt was made to a hood or trunk pin switch that was added 

to the system, or to a light activated entry point if the alarm was installed 

using the voltage sensing feature.

 If the LED is flashing three times...pause...three times...pause...etc., then 

an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will 

only be erased when the ignition key is turned on.

 PUSH BUTTON LED/VALET/OVERRIDE/PROGRAMMING SWITCH: (PBLED)

The PBLED switch allows you to temporarily bypass all alarm functions, eliminating 

the need to hand your transmitter to parking attendants or garage mechanics. When 

the system is in valet mode, all alarm functions are bypassed, however the remote 

panic feature and remote door locks will remain operational. To use the valet mode, 

the system must first be disarmed either by using your keychain transmitter, or by 

activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the PBLED switch until the LED turns on solid. The system 

will remain in the valet mode.

3. To return to normal operation, press and release the PBLED switch any time 

the ignition is on.

 NOTE:

   Always remember to return the vehicle to the valet off position. This will  

ensure that the vehicle remains protected at all times.

MANUALLY OVERRIDING YOUR SYSTEM

 USING THE PBLED OVERRIDE SWITCH 

Your Security System can be disarmed without the use of the keychain transmitter. 

This is necessary, since you will need the ability to operate your vehicle if the 

transmitter is lost or its battery fails. If your system has been selected for Valet 

Switch manual override as indicated on the last page of this manual, to bypass 

the alarm system:

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

Summary of Contents for PRO9644E

















Reviews: