background image

 

VCCS300 Series 

USER MANUAL 

______________________________________________________________________________________________________

 

Page 1 of 22     

Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | 

www.vox-power.com

 

DOC-MN-008-03, VCCS300 User Manual

 

 

 

300W | 600W | 900W 

Scalable 

2” x 4” x 1.61”   

Small 

Fan-less 

Silent 

 

 

Cool it your way:

  

Conduction  |  Convection  |  Forced Air 

 

 

 

 

The VCCS300 series user manual has been prepared by our design team to assist qualified engineers in correctly 

designing in the VCCS300 product into their application to achieve the best reliability and performance possible. 

 

All specifications are believed to be correct at time of publishing. Vox Power Ltd reserves the right to make changes to any of its products and to change or improve any part of the 
specification, electrical or mechanical design or manufacturing process without notice.  Vox Power Ltd does not assume any liability arising out of the use or application of any of its products 
and of any information to the maximum extent permitted by law. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or 
by any products of Vox Power Ltd.  VOX POWER LTD DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS OF ANY KIND WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, 
IMPLIED WARRANTIES OF SUITABILITY, FITNESS FOR PURPOSE, MERCHANTABILITY AND NONINFRINGEMENT.  
Please consult your local distributor or Vox Power directly to ensure that you have the latest revision before using the product and refer to the latest relevant user manual for further information 
relating to the use of the product. Unless specifically otherwise agreed in writing by Vox Power, products sold by Vox Power are not intended for use in connection with life support systems, 
human implantations, nuclear facilities or systems, aircraft spacecraft, military or naval missile, ground support or control equipment used for the purpose of guidance navigation or direction 
of any aircraft spacecraft or military or naval missile or any other application where product failure could lead to loss of life or catastrophic property damage.  The user will indemnify and hold 
Vox Power harmless from any loss, cost or damage resulting from its breach of the provisions.

 

 

VCCS300 Series Overview 

The VCCS300 series of conduction cooled power supplies deliver a silent 300 Watts of power in a miniature 2x4x1.61 Inch package and is the 
ultimate power solution for industrial or medical applications where a high efficiency, ruggedized, noiseless and BF rated power solution with 
Class I or II installation capability is required.   The product series offers power densities exceeding 23W per cubic inch with efficiencies up to 95% 
in a scalable power architecture. The VCCS300 conduction cooled power solution can be scaled up to 600 watts, 900 watts and beyond by 
utilising the onboard current sharing feature. The VCCS300S is approved to the latest industrial safety standards (IEC/UL62368-1 2nd Edition) while 
the VCCS300M is approved to the latest medical safety standards (IEC/UL60601-1 3

RD

 Edition & IEC/UL60601-1-2 4

TH

 Edition). Both versions are 

approved to the latest EMC standards and feature market leading specifications and design-in application support. 

 

 

 

Summary of Contents for VCCS300 Series























Reviews: