background image

22

ENGLISH

PART NAMES AND FUNCTIONS

21. Power switch

Turn this unit power ON/OFF.

CAUTION

 : Before you turn the power on be sure you have made all connections to the mixer. Also be 

sure you amplifiers are turned off. 

CAUTION

 : Remember to avoid damaging pops to the speakers, the mixer is turned on first and turned 

off last.

22. Power cord fastener

To fasten the power cord to avoide unpluging the cord by accident. 

23. Fader start sontrol jack

This jack is used to control the “FADER START” function between the mixer and a compatible Player. Using 
the mini plug included with your player, connect from the player controller out jack to this jack. CH-A “FADER 
START” functionality will be controlled by the left side (A) of the CROSSFADER. CH-B “FADER START” 
functionality will be controlled by the right side (B) of the CROSSFADER. For more information on “FADER 
START” functionality refer to the user manual included with your player. Be sure to only use the mono tip mini 
plug included with your player to avoid damage to the mixer and/or the player.

24. Mic input jack

This jack will accept a standard 1/4” (6.3mm) male plug.

25. GND (GROUND TERMINAL)

Be sure to connect turntable ground leads to either or both of the two available ground terminals. This will 
reduce the humming and popping noises associated with magnetic phono cartridges.

26. LINE/PH (Phono) selector switches

These switches are used to change the mode of phono input jacks 

27

 . When connecting turntable to these 

jacks be sure the switch is in the PH (phono) position, and when using line level input devices select LINE.

REAR PANEL

31

30 29

24

25

25

26

23

21

22

28 27 26 28 27

Summary of Contents for M10















Reviews: