VOX electronics EBI444, User Manual

Page: 86 / 107

EN - 16
Timer Function
The timer function is available in two
versions, as follow.
Minute Minder Timer (1 - 99 min.)
The minute minder timer can be operated
if the cooking zones are switched off. The
timer display will show “ 00 ” with a blinking
dot.
Use the Timer and Sliding Button
to increase/decrease the time.
The range is between 0 and 99 minutes.
If there is no adjustment to the displayed
time within 10 seconds, the minute minder
timer will be set and the blinking dot will
disappear. Once the timer is set, it begins to
count down.
When the timer reaches zero, a signal will
sound and the timer display will blink. The
sound signal will stop automatically after 2
minutes and/or by pressing any button.
The minute minder timer can be changed or
switched off any time by using the Timer
and Sliding Button . Switching off
the hob by pressing at any time will also
switch off the minute minder timer.
Cooking Zone Timer (1 - 99 min.)
When the hob is switched on, an
independent timer can be programmed for
each cooking zone.
Select a cooking zone, then select the
temperature setting and, finally, activate the
timer setting button , the timer can be
programmed to switch off a cooking zone.
Four LEDs are arranged around the timer
that indicate which cooking zone the timer
has been set for.
10 seconds after the last operation, the
timer display will change to the timer that
will run out next (in cases where a timer is
set for more than one cooking zone).
When the timer has run down, a signal will
sound, the timer display will show “ 00 ” and
the assigned cooking zone timer LED will
blink. The programmed cooking zone will
switch off and “ H ” will be displayed if the
cooking zone is hot.
The sound signal and the blinking of the
timer LED will stop automatically after 2
minutes and/or by pressing any button.
Buzzer
While the hob is in operation, the following
activities will be signalled by the buzzer.
• Normal button activation will be
accompanied with a short sound signal.
• Continuous button operation over a
longer period of time (10 seconds)
will be accompanied with a longer,
intermittent sound signal.
Boost Function
To use this function, select a cooking zone
and set the desired cooking level, then
press the “ P ” (Boost) button.
The Boost function can only be activated
if it is applicable with the cooking zone
selected. If the Boost Function is active,
a “ P ” will be shown on the corresponding
display.
Activating the booster can exceed the
maximum power, in which case the
integrated power management will be
activated.
The necessary power reduction is shown
by the corresponding cooking zone display
blinking. Blinking will be active for 3
seconds to allow for further adaptations of
the settings before power reduction.
Error Codes
If there is an error, an error code will be shown on the
heater displays.
E1 Cooling Fan is disabled. Call an authorised
service agent.
E3 Supply voltage is other than the rated values.
Switch the hob off by pressing ,wait until
“ H ” disappears for all zones, switch the hob
on by pressing and continue to use. If
the same error is displayed again, call an
authorised service agent.
E4 Supply frequency is different from the rated
values. Switch the hob off by pressing
, wait until “ H ” disappears from all
zones, switch the hob on by pressing
and continue to use. If the same error is
displayed again, switch the plug for the
appliance off and on. Switch the hob on by
pressing and continue to use. If the same
error is displayed again, call an authorised
service agent.
E5 Internal temperature of the hob is too high,
switch the hob off by pressing and let the
heaters cool down.
E6 Communication error between the touch
control and heater. Call an authorised service
agent.
E7 Coil temperature sensor is disabled. Call an
authorized service agent.
E8 Cooler temperature sensor is disabled. Call
an authorized service agent.