Von Duprin 98/9950WDC Installation Instructions Manual Download

Page: 15 / 16

TOP STRIKE AND COVERS

Adjust top strike as necessary, then install the third

strike screw to fix the strike position.

Metal

Wood

#25 x

³⁄₄

" Deep

#10-24

¹⁄₈

" Drill

Pilot 1" Deep

(metal)

(wood)

For fire devices, prepare door edge and cover plate.

Fire application only
Intumescent must be properly aligned before exposed

adhesive contacts cover plate. Adhesive is permanent and

not repositionable.

³⁄₁₆

" Drill, Pilot 1" Deep x2

Insert plastic
anchors

Peel adhesive backing from
intumescent and apply to
back side of cover plate

b-1

b-2

Install cover plate to door edge, then completely

tighten down center case screws.

For non-fire devices, first
prepare door edge

¹⁄₈

" Drill, Pilot 1" Deep x2

c-1

c-2

Install center case cover.

Remove protective
film from
pushbar

Summary of Contents for 98/9950WDC

















Search results

Summary of Contents for 98/9950WDC

Reviews:

Related manuals for 98/9950WDC

Brands by name

Popular brands

Von Duprin 98/9950WDC, Installation Instructions Manual

Search results

Summary of Contents for 98/9950WDC

Reviews:

Related manuals for 98/9950WDC

Brands by name

Popular brands