Volvo EPA2007 D13F Reference Manual Download Page 86 | Manualshive

Page: 86 / 179

background image

80 ENGINE COMPONENT AND LOCATION

Cylinder Block

W2033309

1. Cylinder Block

2. Block Stiffener Plate

The cylinder block is made of cast iron. For increased cylinder block rigidity and
noise and vibration reduction, a steel stiffener plate attaches to the bottom.

The main and piston lubricating channels are drilled longitudinally through the block.
These are plugged at the front of the block. The main channel opens into a cast-in
channel that supplies oil to the timing gears. The piston cooling channel is covered
by the timing gear cover.

Main bearing caps are made of nodular cast iron machined together with the cylinder
block. Cast alignment slots in the block and tabs on the caps ensure proper alignment
at installation. Each cap is marked with its location beginning with No. 1 at the front.
Cap Nos. 4 and 7 are unique and are not numbered.

The block includes cylinder liners that contact the coolant directly (wet liners). The
casting shape follows the contours of the cylinders to increase rigidity and reduce
noise.

«
...
84
85
86
87
88
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: brel-motors Pages: 2

3564K024BC series

Brand: Faulhaber Pages: 60

Brand: SUHNER Pages: 16

Brand: BMW Pages: 41

Brand: Briggs & Stratton Pages: 200

Brand: O.S. engine Pages: 13

MAX-15CV Series

Brand: O.S. engine Pages: 30

RolloTube Comfort 2360 20 80

Brand: RADEMACHER Pages: 8

RolloTube S-line DuoFern

Brand: RADEMACHER Pages: 8

RolloTube Basis

Brand: RADEMACHER Pages: 60

Brand: RADEMACHER Pages: 64

A50-10L Turnado

Brand: Hacker Pages: 4

Brand: Hacker Pages: 36

Brand: Volvo Pages: 8

Brand: Robin America Pages: 24

Car engines GX640

Brand: Honda Pages: 33

Brand: Honda Pages: 38

Brand: Honda Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands