Volvo EPA2007 D13F Reference Manual Download Page 83 | Manualshive

Page: 83 / 179

background image

ENGINE COMPONENT AND LOCATION 77

Camshaft and Valve Train

W2033300

1. Inlet Valve Yoke (Bridge)

5. Volvo Engine Brake Rocker Arm

2. Inlet Valve Rocker Arm

6. Exhaust Valve Yoke (Bridge)

3. Injector Rocker Arm

7. Shim Retaining Screw

4. Exhaust Valve Rocker Arm

The engine has an overhead camshaft and rocker arm shaft in support of four valves
per cylinder. The camshaft rides on seven journals with a bearing cap and support
block (saddle) at each point. The bearing inserts (shells), bearing caps and support
blocks are replaceable.

In standard configuration (with VGT exhaust brake only), there are three cams for
each cylinder, including inlet, injection and exhaust. There are four cams per cylinder
in the optional configuration (VGT exhaust brake plus Volvo Engine Brake) with the
addition of a "brake" cam at each cylinder.

The rocker arms are positioned on the shaft (front to back) in the order of inlet, injector,
exhaust and brake, if so equipped. Both the inlet and exhaust rocker arms each drive
the valve pairs via a pinless yoke (bridge). On engines equipped with Volvo Engine
Brake, the "brake" rocker arm works in combination with the exhaust rocker arm to
precisely control the opening and closing of the exhaust valves for engine braking.

Exhaust valve yokes include a shim for adjustment. Replaceable valve guides and
seats are made of alloyed cast iron and steel respectively. All valve guides have oil
seals. Exhaust valves have double valve springs.

«
...
81
82
83
84
85
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Kohler Pages: 116

Brand: Danfoss Pages: 32

Brand: RADEMACHER Pages: 60

BAUDOUIN PowerKit 16M33 Series

Brand: WEICHAI Pages: 142

Brand: Globe Pages: 11

Brand: Saito Pages: 2

Brand: GE Pages: 10

Brand: GE Pages: 20

310000 - REVISION C

Brand: GE Pages: 24

Brand: Petter Pages: 58

Brand: DoorHan Pages: 16

Brand: Doosan Pages: 179

Brand: Robin America Pages: 23

Brand: Briggs & Stratton Pages: 11

AM60 ESSENTIAL M

Brand: A'OK Pages: 7

Brand: Ford Pages: 18

Brand: TOSO Pages: 6

Brand: Danfoss Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands