Volvo EPA2007 D13F Reference Manual Download Page 15 | Manualshive

Page: 15 / 179

background image

GENERAL INFORMATION 9

Service Precautions Summary

Following is a summary list of the DO and Don’t issues applying to D13F engine
service:

1

DO NOT

machine the cylinder head for clean-up since this will change injector

depth, thereby affecting emission. It will also upset the ability to correctly adjust
timing gear backlash.

2

DO NOT

grind the injector copper sleeves.

3 Connecting rods and crankshaft main bearing capscrews can be re-used

four

times.

Screw heads MUST be punch marked at each overhaul to indicate the number
of times used.

4 Install the crankshaft main bearing caps according to marked assembly number.

Correct alignment is also critical and is aided by the following:

•

Two casting nipples, located in the cylinder block and on the respective bearing
cap, eliminate incorrect assembly

•

Sleeve pressed into the cylinder block guide the bearing caps into position
for proper alignment

5 Connecting rod caps MUST BE mated to their respective connecting rods due to

the “fractured manufacturing” process used. Also, the rod caps can be installed
only one way because of the difference in spacing between screw holes at each
side of the cap.

6 DO NOT use the lifting eye on the flywheel housing when tilting the engine /

transmission assembly to an angle greater than 15 degrees.

7 Cylinder head installation requires lowering the head onto the gasket, then pulling

the head horizontally against the timing gear mounting plate using through screws.
Pressed bosses in the gasket keep the head from making full contact with the
gasket surface and prevent damage to the rubber sealing rings as the head slides
into position.

8

DO NOT

use starting fluid (ether) on engine equipped with an inlet manifold air

heater element. An explosion could occur.

9 The D13F engine uses a number of O-rings for sealing various fluid joints and

tubes. It is essential that

new

O-rings of the correct material be used whenever

joints are disassembled and reassembled.

«
...
13
14
15
16
17
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Zimmer Pages: 40

Brand: ebm-papst Pages: 11

Brand: Landa Pages: 64

Brand: MTHTrains Pages: 20

AG2210-LP Series

Brand: Beckhoff Pages: 35

Brand: Arrow Shark Pages: 16

Brand: Toro Pages: 37

Brand: O.S. engine Pages: 16

Brand: O.S. engine Pages: 46

Brand: Volvo Pages: 8

Brand: Yanmar Pages: 160

Brand: Hino Motors Pages: 216

Brand: Hino Pages: 278

Brand: Honda Pages: 2

Brand: Stiga Pages: 65

Brand: DLE Pages: 4

Brand: Honda Pages: 65

5.6-690 GLIDER - V1.3

Brand: MVVS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands