Volvo 2016 s60 inscription Owner'S Manual Download Page 112

Page: 112 / 344

04 Climate

110

Option/accessory, for more information, see Introduction.

Electronic climate control (ECC)

ECC (Electronic Climate Control) helps main-

tain the selected temperature in the passen-

ger compartment and the temperature can be

set separately on the driver's and passenger's

sides.
The AUTO function (p. 112) automatically

regulates the temperature, air conditioning,

blower speed, recirculation and air distribu-

tion.

Related information

•

Climate – general information (p. 107)

Heated seats

The front seat heating has three levels to

increase comfort for the driver and passenger

in cold weather.
The rear outboard seat heating has three lev-

els to increase comfort for the passengers in

cold weather.

Heated front seats*

The current seat temperature setting is shown in

the center console display

Press the lower section of

the button repeatedly until

the desired number of indi-

cator lights illuminate:
Highest heat level – three

indicator lights.

Medium heat level – two indicator lights.
Lowest heat level – one indicator light.

If no indicator lights are illuminated, the seat

heating is switched off.
Seat heating will automatically switch off

when the engine is switched off.

Starting the seat heating automatically

This setting starts heating the driver's seat (at

the highest level) automatically when the

engine is started if the ambient temperature is

below approx. 50° F (10° C).
Activate/deactivate this function in the

MY CAR

menu system, under

Settings

Climate settings

Auto start driver seat

heater

Heated rear seats*

Heat control for the outboard seating posi-

tions is done in the same way as for the front

seats.

Summary of Contents for 2016 s60 inscription
























































































































































































































































































































































Search results

Summary of Contents for 2016 s60 inscription

Reviews:

Related manuals for 2016 s60 inscription

Brands by name

Popular brands

Volvo 2016 s60 inscription, Owner'S Manual

Search results

Summary of Contents for 2016 s60 inscription

Reviews:

Related manuals for 2016 s60 inscription

Brands by name

Popular brands