Volvo Penta TAD1340VE Operator'S Manual Download

Page: 94 / 106

Lubrication System

Oil change volume, including filter change

Composite sump (Standard)

48 liters (12.68 US gal)

Aluminum sump (Optional)

55 liters (14.53 US gal)

TAD1650VE (Aluminum sump, Standard)

55 liters (14.53 US gal)

Additional volume:
Remote oil filters (Optional)

3 liters (0.80 US gal)

Oil pressure, hot engine

at operating speed

300-650 kPa (44–94 psi)

TAD1650VE

400–650 kPa (58–94 psi)

Oil filter

Full flow filter

By-pass filter

Lube oil pump

Type

Gear driven

Oil recommendations

Type designation

Oil quality

Oil change interval, reached first in

operation:

TAD1640GE-B, TAD1641GE-B,
TAD1642GE-B, TWD1643GE,
TWD1644GE, TWD1645GE, TAD1650GE,
TAD1651GE, TWD1652GE, TWD1653GE
TAD1640VE-B, TAD1641VE-B,
TAD1642VE-B, TAD1643VE, TAD1650VE

VDS-3
VDS-2

600

hours or 12 months

TAD1650VE-B, TAD1651VE
TAD1643VE-B

VDS-3
VDS-4.5

500

hours or 12 months

VDS = Volvo Drain Specification

Viscosity

Select the viscosity according to the table.

The temperature values refer to stable ambient
temperatures.

* SAE 5W/30 refers to synthetic or semi-synthetic oils.

Technical Data

47711296 01-2019 © AB VOLVO PENTA

Summary of Contents for TAD1340VE











































































































Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands

Volvo Penta TAD1340VE, Operator'S Manual

Search results

Summary of Contents for TAD1340VE

Reviews:

Related manuals for TAD1340VE

Brands by name

Popular brands