Volvo Penta D16 Operator'S Manual Download

Page: 66 / 90

Fuel system, bleeding

The fuel system must be vented after a filter change,
e.g. if the fuel tank has been run dry or after a long-
term stoppage.

Stopped engine

Change-over filter

1 Place a suitable container underneath the fuel filter.

2 Remove the protective cap from the venting nipple

(

) on the filter holder. Connect a transparent hose

to the nipple and lead it to the recovery container.

3 Open the venting nipple and pump fuel with the

hand pump (

) until the fuel is free from bubbles.

Close and tighten the venting nipple while fuel is
running out.

4 Remove the hose and fit the protective cap back

onto the venting nipple.

5 Run the engine at idle for a few minutes to remove

any remaining air from the system. The close the
venting nipple (

) on the engine and check that it

does not leak.

P0021994

Maintenance

47711740 05-2019 © AB VOLVO PENTA

Summary of Contents for D16



























































































Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands

Volvo Penta D16, Operator'S Manual

Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands